JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36 Скачать руководство пользователя страница 31

Страница: 31 / 33

WWW.JEIUK.COM

RAILBEAST RDP-36

This document is protected by copyrights.

Copying, using, or distributing without permission of Ansa Group Ltd is prohibited.

5. DECLARATION OF CONFORMITY

EC Declaration of Conformity

JEI DRILLING & CUTTING SOLUTIONS LTD

UNIT 21 EMPIRE BUSINESS

ENTERPRISE WAY

BURNLEY, LANCASHIRE, BB12 6LT

declare with full responsibility that:

RAILBEAST RDP-36 Petrol Rail Drilling Machine

is manufactured in accordance with the following standards:

•

EN ISO 12100:2012

and satisfies safety regulations of the guideline 2006/42/WE.

Person authorized to compile the technical file:

David McFadden, Unit 21 Empire Business Park,

Burnley

Burnley, 12

February 2020

___________________________

David McFadden

Managing Director

Содержание RAILBEAST RDP-36


































Результаты поиска

Содержание RAILBEAST RDP-36

Отзывы:

Бренды по названию

Популярные бренды

JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36, Руководство оператора

Результаты поиска

Содержание RAILBEAST RDP-36

Отзывы:

Бренды по названию

Популярные бренды