Jeep 2014 Patriot Скачать руководство пользователя страница 48

Страница: 48 / 51

Any abrasive cleaning pad (such as steel wool) or abrasive brush
Any cleaner that contains an acid which can react with and discolor the
chrome surface.

Many wheel cleaners contain acids that can harm the

wheel surface.

Oven cleaner
A car wash that uses carbide-tipped wheel cleaning brushes or acidic
solutions.

STUD, WHEEL, FRONT

REMOVAL

1. Access and remove front brake rotor. Refer to

ROTOR, BRAKE,

REMOVAL

Fig. 35: View Of Wheel Mounting Stud Removal Using 8677

Courtesy of CHRYSLER GROUP, LLC

2. Install Remover (special tool #8677, Remover, Ball Joint) (3) on the hub

NOTE:

Use the following procedure to remove one of five studs
on one wheel hub.

CAUTION: Do not hammer wheel mounting studs out of

the hub. Damage to the wheel bearing will
occur, leading to premature bearing failure.

2014 Jeep Patriot Limited

2014 SUSPENSION Tires & Wheels - Service Information - Compass & Patriot

Tuesday, July 19, 2016 10:01:58 AM

Page 48

Содержание 2014 Patriot




















































Результаты поиска

Содержание 2014 Patriot

Отзывы:

Похожие инструкции для 2014 Patriot

Бренды по названию

Популярные бренды

Jeep 2014 Patriot, Информация о сервисе

Результаты поиска

Содержание 2014 Patriot

Отзывы:

Похожие инструкции для 2014 Patriot

Бренды по названию

Популярные бренды