Jeep 2014 Patriot Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 51

Jeep 2014 Patriot Скачать руководство пользователя страница 32

the head of the changer (located at 1) in a clockwise direction before
rotating the wheel (also in a clockwise direction) to mount the tire. Use
this procedure on both the outer and inner tire beads.

Fig. 23: Mounting Tire Using Rotating Tool Machine

Courtesy of CHRYSLER GROUP, LLC

b. Rotating Tool Tire Changers - Position the wheel on the changer so that

the sensor valve stem (1) is located approximately 210° clockwise from
the installation end of the mounting/dismounting tool (2) once the tool
is mounted for tire installation. Make sure the sensor is clear of the
lower bead breaker area (3) to avoid damaging the sensor when the
breaker rises. Rotate the tool (2) in a counterclockwise direction to
mount the tire. Use this procedure on both the outer and inner tire
beads.

1 - HEAD OF CHANGER LOCATED HERE
2 - VALVE STEM

1 - VALVE STEM
2 - INSTALLATION END OF MOUNTING/DISMOUNTING
TOOL
3 - BEAD BREAKER (KEEP CLEAR OF SENSOR)

2014 Jeep Patriot Limited

2014 SUSPENSION Tires & Wheels - Service Information - Compass & Patriot

Tuesday, July 19, 2016 10:01:58 AM

Page 32

32

«
...
30
31
32
33
34
...
»

Содержание 2014 Patriot




















































Отзывы:

Нет отзывов