Jeep 2008 Liberty Скачать руководство пользователя страница 391 | Manualshive

Страница: 391 / 493

Jeep 2008 Liberty Скачать руководство пользователя страница 391

1. Wear eye protection and remove all metal jewelry such
as watchbands or bracelets that might make an unin-
tended electrical contact.

2. When boosting from a battery in another vehicle, park
that vehicle within booster cable reach, but without
allowing the vehicles to touch.

WARNING!

Do not permit vehicles to touch each other as this
could establish a ground connection and personal
injury could result.

3. Set the parking brake, place the automatic transmis-
sion in PARK (or NEUTRAL for manual transmission),
and turn the ignition OFF for both vehicles.

4. Turn OFF the heater, radio and all unnecessary elec-
trical loads.

5. Connect one end of the jumper cable to the positive
battery post. Connect the other end of the same cable to
the positive terminal of the booster battery.

6. Connect the other cable, first to the negative terminal
of the booster battery and then to the engine ground of
the vehicle with the discharged battery. Make sure you
have a good contact on the engine ground.

WHAT TO DO IN EMERGENCIES

391

6

«
...
389
390
391
392
393
...
»

Содержание 2008 Liberty














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды