Jeep 2008 Liberty Скачать руководство пользователя страница 389 | Manualshive

Страница: 389 / 493

Jeep 2008 Liberty Скачать руководство пользователя страница 389

5. Raise the vehicle by turning the jack screw to the right.
Raise the vehicle only until the tire just clears the surface
and enough clearance is obtained to install the spare tire.
Minimum tire lift provides maximum stability.

WARNING!

Raising the vehicle higher than necessary can make
the vehicle less stable and cause an accident. It could
slip off the jack and hurt someone near it. Raise the
vehicle only enough to remove the tire.

6. Remove the lug nuts and wheel.

7. Position the spare wheel/tire on the vehicle and install
lug nuts with cone-shaped end toward wheel. Lightly
tighten the nuts. To avoid the risk of forcing the vehicle
off the jack, do not tighten the nuts fully until the vehicle
has been lowered.

8. Lower the vehicle by turning the jack screw to the left,
and remove the jack and wheel blocks.

9. Finish tightening the lug nuts. Push down on the
wrench while tightening for increased leverage. Alternate

Rear Jacking Location

WHAT TO DO IN EMERGENCIES

389

6

«
...
387
388
389
390
391
...
»

Содержание 2008 Liberty














































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды