P/N 960-100175R_Rev. 4 {EDP #200824}
© 2013, Japan CashMachine Co., Limited
6 - 3
Calibration and Testing
Taiko™ Series Banknote Acceptor
Section 6
d)
Follow the instructions shown on the Screen
to complete the installation.
e)
A
PdbConv.exe
Icon will be created on the PC
desktop Screen.
4. Convert the Taiko™ Software Data File to begin
running the “
Pdb
” format as follows:
a)
Double Mouse-click on the
PdbConv.exe
Icon
to start the ‘
PdbConvEN
’ Program. The Figure
PdbConv Ver. 2.0.1
Screen will appear.
b)
Mouse-click on the
Download File
Tab
a
) to select the conversion
option required for your particular system
requirements.
c)
Mouse-click on the appropriate Screen Button
to select the file you want converted. Confirm
that the File name listed in the download
Filename
: Field is correct (See Figure 6-6
c
),
and Mouse-click on the “
…
”
Screen Button
b
) to Select the file you want
to convert. The file name will be similar to
“
p11_10621a.usa
”.
d)
Mouse-click on the
Convert PDB
Screen
d
) to begin the
conversion process.
e)
When the Cyclic Redundancy Check Sum
(CRC) is displayed (See Figure 6-7
a
), the
conversion is complete.
f)
Click the
Finish
e
) to close the ‘
PdbConv.exe
’ application.
5. Transfer the newly created Files to the Palm
Pilot
®
handheld as follows:
a)
“
ID003DWN.prc
” and the
b)
.pdb
file previously created during Step 4d.
6. Download files into the Taiko™ unit as follows:
a)
Refer to Figure 6-2 on page 6-1 to properly
connect the Palm Pilot
®
to the Taiko™ Unit.
b)
Turn DIP Switches #1, #7 and #8 to ‘
ON
’.
c)
Supply power to the Taiko™ Unit. The
Green
Front Panel Bezel light will begin to flash.
d)
Tap on the On the Palm Pilot
®
start-up screen
DWN-03 Icon. The
Program Download
Screen
shown in Figure 6-7 will then appear.
7. Tap
on
area
?
shown in Figure 6-7 and the Soft-
ware Version information currently installed in
the Taiko™ Unit will appear.
8. Tap
on
area
?
and select the desired Software
Version to be downloaded.
9. Tap on the send Screen Button to begin down-
loading if the
Yellow
LED is lit steady (ON).
10. When downloading is complete, the Screen will
automatically return to the Screen previously
shown.
Writing a New Serial Number
Upgrading/Replacing Software
The initial software downloading procedure has
been described previously in the "Software Down-
loading Procedure" on page 6-2 of this Section.
However, when the Taiko™ Software has been
upgraded or the Taiko™ Unit’s CPU Board has
been replaced, new software must be downloaded
to the Taiko™ Unit.
When downloading software files from a Palm
Pilot
®
handheld PDA, please refer to the proce-
dures outlined in "Palm Pilot Program Installation"
on page 6-2 of this Section.
P
ROGRAMMING
R
EQUIREMENTS
When downloading new software, the following
items will be required:
•
PC (OS: Windows
®
98 SE/2000/XP)
•
JCM Taiko™ Banknote Acceptor (PUB-7 or
PUB-11)
•
Downloader Application (Download Program
Ver.1.21.exe)
•
Software Program (Ex. P07X3102.G_S)
•
JCM External Power Supply (JAC# 501-
000187RA, EDP# 116125) or equivalent.
•
Taiko™ Harness “A” (JAC# 400-100551RA,
EDP# 121797)
•
VM-450 Harness (JAC# 400-100643RA,
EDP# 739571).
Figure 6-6
Taiko Palm Conversion Screen
a
c
d
b
e
NOTE: The following two (2) files will need
to be transferred into the Palm Pilot
®
memory first.
NOTE: Refer to the Palm Pilot
®
Manual
for instruction on loading a .pcr and .pdb
file into the particular handset being used.
Figure 6-7
Taiko Palm Program Download Screen
a