P/N 960-100175R_Rev. 4 {EDP #200824}
© 2013, Japan CashMachine Co., Limited
6 - 2
Section 6
Taiko™ Series Banknote Acceptor Calibration
and
Testing
Software Download Preparation
The following instructions describe how to decom-
press and store a downloaded program onto a PC
for eventual installation into the Taiko™ Banknote
Acceptor:
1. Refer
Figure 6-1 interconnection diagram to
properly connect the power supply, various
cables and wiring Harnesses to the PUB-7/11.
2. Figure 6-4 illustrates the Taiko’s external Ports,
DIP Switch Block locations and its initial Switch
settings. To prepare the PUB-7/11 for a software
download, set the DIP Switches as follows:
–
Set DIP Switch No.1, 7 and 8 to ‘
ON
’
–
Set DIP Switches No.2 through 6 ‘
OFF
’.
3. Supply power to the PUB-7/11. The
Green
Front
Panel Indicator LED will begin flashing approxi-
mately once every second.
Software Downloading Procedure
PC Program Installation
The following PC initialization functions are
required prior to downloading software:
1. Create and name a new PUB Folder on your PC.
2. Decompress the Palm Pilot
®
Programing .ZIP
File and save the expanded file program contents
in the PUB file Folder just created.
3. Open the Folder and Double Mouse-click on
“
Ver.1.20.exe
” of the expanded PUB-7/11 PC
Download Program. The
Download Program
Ver.1.20
Screen shown in Figure 6-5 will appear.
4. Mouse-click
on
the
BROWSE
Screen Button
a
) and select the desired Software
Program required for installation (i.e., example =
Pll.10801.usa2
).
5. Select an available PC COM Port Number from
the “
Port
” pull-down Menu (See Figure 6-5
b
).
6. Confirm that a Baud Rate of 38400 is selected; if
not, set the Baud Rate to 38400 from the “
Baud-
rate
” pull-down Menu (See Figure 6-5
c
).
7. Mouse-click on the large [
Start Download
]
Screen Button (See Figure 6-5
d
) to begin down-
loading the selected Software File.
8. When downloading is complete, the Taiko™
Front Panel LED will turn a
Blue
Color.
9. Turn the Taiko™ power ‘
OFF
’, and remove the
programing connections from the Taiko™ Unit.
Palm Pilot Program Installation
The following Palm Pilot
®
PDA initialization func-
tions are required prior to downloading Software:
1. Create and name a new PUB Folder on your PC.
2. Decompress the Palm Pilot
®
Programing .ZIP
File and save the following expanded file
program contains in the Folder just created:
a)
“
PdbConvEN.exe
”
b)
“
ID-003DWN.exe
”
3. Prepare
the
Conversion Program as follows:
a)
Open the folder created during Step 1 and
Double Mouse-click on File Converter
program “
PdbConvEN.exe
”.
b)
Save the Files created in the previously
created File Folder (i.e., “
Setup.exe
”,
“
SETUP.LST
” and “
PdbConv.CAB
”).
c)
Double Mouse-click on the “
Setup.exe
” File
to start to the program installation procedure.
Figure 6-3
Typical Tungsten Series Palm Pilot
Handheld with JCM Software Icons
c
b
a
a) Palm Flash Program
b) PalmA66US Program
c) PSP-02 Program
WARNING: Make sure the External
Power Supply is OFF when connecting
the Harnesses to the Taiko™ PUB-7/11.
Failure to do so may cause electrical
shock and/or permanent damage to the
equipment.
Figure 6-4
Taiko DIP Switch & Port Location
ON
DIP Switch Block
Interface
Connector
Maintenance
Connector
Optional
Connector
Figure 6-5
Taiko PC Download Program Screen
a
b
c
d