![background image](http://html2.mh-extra.com/html/jcm/dbv-series/dbv-series_operation-and-maintenance-manual_3535895090.webp)
P/N 960-000180R_Rev. 1 {EDP #233427}
© 2016, JAPAN CASH MACHINE CO., LTD.
A - 2
Appendix A
DBV® Series DBV-400 Banknote Validator
Troubleshooting
Adjustment Error
Table A-2 lists the various possible DBV-400 Unit Adjustment fault conditions.
Acceptance rates
Dirt and/or stains on the
Rollers and Lenses
Clean the Transport Path. Refer to the “Cleaning Procedure” on page 2-11.
The Unit has been
disassembled, and calibration
adjustments have not
occurred following a
reassembly.
Calibrate the Sensors after reassembling the DBV-400 Unit.
The wrong Software version
or an older Software version
is being used.
Make sure that the programmed Software is the latest version, and it
supports the Currency values for the specific Country (e.g., check
denomination/issuing year).
Software not designed to
accept current Banknotes
Check the particular specifications for the required Banknote Type
Acceptance, and make sure the Banknotes will be accepted by the Software
loaded (e.g., check denomination/issuing year).
All Banknotes being
rejected
Incorrect software
(different Currency type)
Download the correct Software for the Currency being accepted.
Banknotes are not being
accepted by the Software.
Make sure the Banknote values required are included in the Software
Specifications (e.g., denominations/issuing year).
Incorrect DIP Switch settings
Enable all denominations by setting all DIP Switches to OFF.
Banknote acceptance is being
inhibited by a Host Controller
command.
Enable Banknote acceptance for the required Host Command.
Validation Sensor failure
Change the CPU Board and Sensor Board and calibrate the Sensors.
Unit was disassembled and
calibration did not occur
following reassembly
Calibrate all Sensors following reassembly.
Motor
continues to run
A foreign object or a jammed
Banknote is stuck in the
Transport Path.
Open the Validation Guide (refer to Figure 2-7) or Cash Box Door (refer to
Figure 2-3 or Figure 2-4), remove the foreign object or jammed Banknote, and
then close the Validation Guide or Cash Box Door.
Motor Driver failure
Conduct a Forward/Reverse Motor Rotation Test.
Cannot enter the
TEST mode
Incorrect DIP Switch settings
Set the DIP Switch DIP SW1 #8 to ON, and reapply power to the DBV-400 Unit.
DIP Switch failure
Refer to “DIP Switch Test” on page 6-13 regarding the DIP Switch Test, and
conduct a DIP Switch TEST to check if the specific DIP Switch Block contains
a failure.
CPU Board failure
Exchange the CPU Circuit Board with a known good Circuit Board and
calibrate the Sensors.
Table A-2
Adjustment Fault Conditions
Symptoms/Error
Messages
Possible Fault Causes
Corrective Action Required
Cannot start the
Sensor Adjustment
program from JCM
Tool Suite
PC Operating System (OS) is
not compatible
The current Adjustment program only supports the Windows 2000/XP/
Windows 7 Operating Systems.
The Program Files are
corrupted.
Request the correct programs from JCM.
Communication Error
Wrong or inappropriate
connections
Check the PC Harness connections and the related DBV-400 Interface
Connectors for damage. Check for any bent, missing or damaged Pins in the
Connector Plugs and/or Receptacles.
DBV-400 Switch settings
are incorrect.
Reset the DIP Switch DIP SW1 #8 to ON, and reapply power to the DBV-400
Unit.
DIP Switch failure
Refer to “DIP Switch Test” on page 6-13 regarding DIP Switch settings and
conduct a DIP Switch Test.
CPU Board failure
Exchange the CPU Circuit Board with a known good Circuit Board.
Adjustment Error
Incorrect Reference
Paper type
Follow the instructions provided in the “DBV-400 Calibration Tool for
Maintenance.exe” Program and use the correct Reference Paper.
Validation Sensor failure
Change the CPU Board and Sensor Board.
Table A-1
General Fault Conditions (Continued)
Symptoms/Error
Messages
Possible Fault Causes
Corrective Action Required