background image

JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092  

Kickback is the result of saw 
misuse and/or incorrect operating 
procedures or conditions and 
can be avoided by taking proper 
precautions as given below.

a)  Maintain a firm grip with both 
hands on the saw and position 
your arms to resist kickback 
forces. Position your body to 
either side of the blade, but not 
in line with the blade. 

Kickback 

could cause the saw to jump 
backwards, but kickback forces 
can be controlled by the operator, 
if proper precautions are taken.

b)  When blade is binding, or 
when interrupting a cut for any 
reason, release the trigger and 
hold the saw motionless in the 
material until the blade comes to 
a complete stop. Never attempt 
to remove the saw from the 
work or pull the saw backward 
while the blade is in motion or 
kickback may occur. 

Investigate 

and take corrective actions to 
eliminate the cause of blade 
binding.

c)  When restarting a saw in the 
workpiece, centre the saw blade 
in the kerf and check that saw 
teeth are not engaged into the 
material. 

If saw blade is binding, 

it may walk up or kickback from 
the workpiece as the saw is 
restarted.

d)  Support large panels to 
minimise the risk of blade 

pinching and kickback. 

Large 

panels tend to sag under their 
own weight. Supports must be 
placed under the panel on both 
sides, near the line of cut and 
near the edge of the panel.

e)  Do not use dull or damaged 
blades. 

Unsharpened or 

improperly set blades produce 
narrow kerf causing excessive 
friction, blade binding and 
kickback.

f)  Blade depth and bevel 
adjusting locking levers must 
be tight and secure before 
making cut.

 If blade adjustment 

shifts while cutting, it may cause 
binding and kickback.

g)  Use extra caution when 
making a "plunge cut" into 
existing walls or other blind 
areas. 

The protruding blade 

may cut objects that can cause 
kickback.

SAFETY INSTRUCTIONS 
FOR SAWS WITH OUTER 
PENDULUM GUARD, 
INNER PENDULUM 
GUARD, OR TOW GUARD 

Lower Guard Function

a)  Check lower guard for proper 

closing before each use. Do not 

operate the saw if lower guard 

does not move freely and close 

instantly. Never clamp or tie 

the lower guard into the open 

Содержание JCB-CS1500

























Отзывы: