JBL SRX900 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 50

background image

44

Rigging Manual

STEPS (Continued):

• Remove the link pin and install the stop pin into the angle selection plate of the first SRX9xxLA cabinet.

• Place the first SRX9xxLA cabinet onto the base plate and pin the front two corners using the attached pins.

• Lift the back of the SRX9xxLA and set the base plate’s angle selection plate to the desired angle. Pin the SRX9xxLA cabinet

and the base plate’s angle selection plate using the LINK PIN hole and pin.

4

5

CAUTION: Safe limits for ground-stacked arrays always assume that the stacking surface (floor and stage) is flat .
Do not deploy ground-stacked arrays on non-flat surfaces to avoid tipping hazards .

6

5

4

6

«
...
42
43
44
45
46
...
»

Содержание SRX900 Series



















































Отзывы:

Нет отзывов

Похожие инструкции для SRX900 Series

Бренд: DaytonAudio Страницы: 2

Бренд: DaytonAudio Страницы: 12

Бренд: DAY Страницы: 24

Бренд: Fender Страницы: 18

Бренд: iDance Страницы: 9

Бренд: JBL Страницы: 4

Simply Cinema ESC300

Бренд: JBL Страницы: 10

Бренд: JBL Страницы: 27

Бренд: JBL Страницы: 12

Бренд: JBL Страницы: 10

Бренд: JBL Страницы: 6

Бренд: JBL Страницы: 2

MCX-A10 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 56

Бренд: Yamaha Страницы: 17

Pit Boss Sportsman 7 Series

Бренд: Dansons Group Страницы: 51

SoundStage SSR43

Бренд: Vantage Point Products Страницы: 2

Бренд: Nady Audio Страницы: 2

Бренд: LEXIBOOK Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды