5
Wall Mounting the Speakers
Important safety note: Proper selection of mounting hardware not included
herein and proper assembly and installation of brackets, including but not
limited to selection of appropriate weight bearing support and bracket use with
the specified speaker only is the exclusive responsibility of the customer.
Manufacturer disclaims any liability for the selection of mounting hardware and
or bracket installation.
a. Loosen and remove the molded nut ™ by turning it counter clockwise. Use
the supplied metal bar
∞
if necessary by inserting it in one of the holes on
the molded nut ™.
b. Pull the ball/shaft £ out of the wall bracket ¢.
c. Slide on the molded nut ™ onto the ball/shaft £ with threaded opening facing
the ball, and thread on the metal nut ¡ all the way onto the ball/shaft £, with
the nut ¡’s ”knurled” surface facing away from the ball.
d. Screw on the ball/shaft £ into the threaded insert on the back of the speaker
cabinet § until it is fully seated against the bottom of the insert.
e. Tighten the ”knurled” nut ¡ using a crescent wrench until it is firmly seated
against the back of the speaker and has fully locked the ball/shaft £ and the
speaker cabinet together. Pleace note that once this nut is tightened, it may
embed some marks on the back of the speaker where the attachment is
made. However, these marks will be covered by the nut ¡.
f. The back-up cord • provided as an additional measure to prevent the fall of
the speaker in case the speaker becomes detached from the wall bracket.
One of the two lower screws ª that attach the wall bracket ¢ to the wall, will
need to go through the eyelet ⁄ at the end of the cord before going through
the wall bracket hole. Mount the wall bracket ¢ onto a wood stud on the wall,
using #10, minimum 1 inch long, pan head wood screws. Make sure that all 4
screws are driven into the stud and not in drywall. If the bracket needs to be
Adjusting the Volume
When using the JBL OnAir Control 2.4G wireless speaker system, turn the vol-
ume level on your receiver to approximately half-way. If using with a portable
audio device, turn its volume control to the maximum output. From this point
on, you will use the remote control included with the JBL OnAir Control 2.4G
wireless speaker system to adjust the volume.
To raise the volume, simply push up
1
on the remote control
To lower the volume, simply push down
2
on the remote control
Local Input
The JBL OnAir Control 2.4G wireless speaker system also includes a local
input
8
on the rear of the Active Speaker. This input allows you to hook up a
portable audio player directly to the speaker wherever you may happen to be.
For example, you could have the system connected to your receiver as
described in Application 2, listening to a local FM station and then hook up
your portable music player to the local input and switch between the two dif-
ferent sources.
To connect portable audio player to the Active Speaker, simply connect the
headphone jack to the Line-In
8
on the rear of the Active Speaker using a
1/8” mini-jack – 1/8” mini-jack cable (Not included).
To switch between the two sources, push the Input button
(show button or #)
on the remote control.
Indicator Light Information
P
Po
ow
we
err IIn
nd
diic
ca
atto
orr LLE
ED
D
IIn
np
pu
utt LLE
ED
D
((T
To
op
p))
((B
Bo
otttto
om
m))
G
Grre
ee
en
n
System is on
Transmitter and speaker are
communicating (RF lock)
B
Blliin
nkkiin
ng
g G
Grre
ee
en
n
Receiving IR command
Transmitter and speaker are not
from remote control
communicating (No RF lock)
R
Re
ed
d
Standby
(no signal being received)
O
Orra
an
ng
ge
e
Local input is selected
A Word About Wireless Products
The JBL OnAir Control 2.4G wireless speaker system utilizes and advanced
wireless transceiver operating in the 2.4GHz frequency band. This is the same
frequency band that is used for wireless home networks and high-quality
cordless phones. It also allows for the transmission of high-performance, full-
spectum sound to remote locations, wirelessly.
Interference
In the unlikely event that you experience interference when operating the sys-
tem you may change the channel in which the system operates. On the
Transmitter Module and the Active Speaker, there is a four-position “ID Code”
selector. Simply set the selectors to one of the other positions. The Transmitter
and Active Speaker must be set to the same position in order for the system to
function correctly.
Range
Like all wireless devices, the JBL OnAir Control 2.4G wireless speaker’s oper-
ating range may vary depending upon variables such as building construction
methods and materials, atmospheric conditions and other sources of interfer-
ence. Please consult your JBL dealer or distributor or visit us at www.jbl.com
for further information or assistance.
Wall and Stand Placement
Adjustable wall brackets are included for the two speakers and transmitter
module. The included bracket is for wall mounting only. It is not to be used for
ceiling mount.
OPERATION
Содержание On Air Control 2.4G
Страница 1: ...CONTROL 2 4G ON AIR OWNER S GUIDE...
