background image

3

14

Installation

1. Precautions

2. Mounting angle adjustment

3. Supporting the unit

Choose the mounting location carefully so that the unit will not interfere with the normal
driving functions of the boat.

Avoid installing the unit where it would be subject to high temperature (such as from direct

sunlight or hot air) or where it would be subject to dust, dirt or excessive vibration. Use only
the supplied mounting hardware for a safe and secure installation.

Adjust the mounting angle to less than 20 degrees from the horizontal position. Otherwise,
the unit will skip beyond its intended level.

Failure to support the unit with the back bracket will reduce the life of the unit due to
possible CD mechanism imbalance.

1. UNIT
2. HEX NUT
3. SPRING WASHER
4. PLAIN WASHER
5. BODY
6. REAR SUPPORT STRAP
7. TAPPING SCREW
8. M5 X 20 HEX BOLT

4

1

3

Accessories subject to change without notice.

If the fuse blows, check the power connection and replace the fuse. If the fuse blows
again after the replacement, there may be an internal malfunction. In this case, consult
your nearest dealer.

Use the specified amperage fuse for each lead.
Use of a higher amperage fuse may cause serious damage.

1. Fuse replacement

2. Warning

2

9

6

Spring Washer

5

7

HEX

Spring Washer

Plain Washer

6

Trouble shooting Guide

Caution

1. CONNECTOR PINS: Always keep connector pins clean.

If the PIN connector looks dirty, use cotton tips to clean it, so as to avoid any unexpected
malfunction caused by dirt.

2. In many respects, a stereo acts much like a computer and occasionally requires a reboot.

In the unlikely event of product malfunction, a reset can usually fix the issue.

A reset is accomplished by holding the BAND and Preset 1 button simultaneously

until the unit turns off.

Issue

No power

No Sound

No Reception

Cause

1. Incorrect wiring
2. Fuse is blown
3. Low battery voltage

1. Speaker connection

came loose

2. Bad speaker

3. Output blown
4. Volume too low on

media device

1. Antenna not firmly

seated in socket

Solution

1. Double check wiring
2. Replace fuse
3. Check voltage of vehicle battery

with multimeter. Voltage must
be at least 11V.

1. Double check connections.

2. Replace bad speaker with known

good speaker and connect.

3. Send unit in for repair.
4. Increase volume of media device

1. Insert firmly.

Содержание MR-18.5










Отзывы: