Installation guide
SAILOR 6300 MF/HF Transceiver Unit
& Antenna Tuning Unit 150/250/500W
How to connect the antenna
How to install the Antenna Tuning Unit mounting bracket
How to install the Transceiver Unit 150/250W
1. Nut M10
2. Tooth lock washer M10
3. Fitting for mast
4. Mountingplate for ATU
5. Treadrod M10
Disclaimer
105
mm
350
mm
3 6 0 m m
3 9 1 m m
35
mm
1 5 0 m m
M i n .
3 7 9 m m
1 5 0 m m
M i n .
3 6 0 m m
Space for
cable access
Space for
service
4 x ø8mm
4
4
3
mm
4 x ø6mm
2 3 . 5 m m
8 8 m m
1 4 5 m m
5 0 0
M i n .
m m
Space for airflow
and service
Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying
documentation is disclaimed by Thrane & Thrane. The information in this manual is provided for information purposes
only, is subject to change without notice and may contain errors or inaccuracies. Manuals issued by Thrane & Thrane
are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g.
from
cobham.com/satcom
or from the distributor
.
Thrane & Thrane is not responsible for the content or accuracy of
any translations or reproductions, in whole or in part, of this manual from any other source.
Thrane & Thrane A/S trading as Cobham SATCOM.
1
2
3
4
1
3
5
4
2
1. Pan head screw M6x16 mm
2. Washer M6
3. Hexagon head screw M6x10 mm
4. Flat washer ø6.4xø12x1.6 mm
How to install the Antenna Tuning Unit 150/250W
Space for cable and
service access
164
mm
164
mm
2 7 1 m m
1 5 0
M i n .
m m
75
mm
12
mm
80
mm
2 0 0 m m
352
mm
504
mm
5 0 0
M i n .
m m
5 0
M i n .
m m
Space for
service access
Space to nearest overhang
80
mm
2 9 0 m m
1000
mm
200
mm
4
2
1
1
3
3
5
6
Wire length 4 metres
Optional accessories:
Mounting plate and fittings for mast part no 737589.
Mounting plate only - part no 737588.
Cable fitting
In general a 12 metres antenna installation is preferred and can be made using an 8
metres whip and 4.5 metres feeder or a 10 metres whip and 2.5 metres feeder. In both
cases the whip should be mounted on a pole providing sufficient height to have the
Antenna Tuning Unit mounted such that it allows for the feeder to be erected at an
angle of 45 to 60 degrees, creating a combined 12 metres vertical antenna system.
The feeder wire is terminated at the antenna horn at the top of the Antenna Tuning
Unit. Use a supporting insulator near the ATU to carry mechanical stress from the
feeder wire. Use a short flexible part of the feeder wire between the supporting
insulator and the ATU horn in order not to ap-
ply mechanical stress to the antenna horn.
To maximize the radiated power and avoid flash
over, keep distance to metal parts as long as
possible, preferable more than 100 mm. Use a
short direct ground connection from the ground
clamp at the bottom end at the Antenna Tuning
Unit to nearest suitable metal ground plane.
It is recommended to use the ATU mounting
bracket for the physical fitting of the ATU.
For further information, download the installation
manual 98-144591 at www.cobham/satcom.
Optional accessories:
Antenna connection kit
part no 405301A-905.
1. Shackle
2. Isolator
3. Wire clamp
4. Wire
5. Cable tie
6. Wire lug
