17
4. PRESET SCAN BUTTON
Button for scanning preset station
frequencies (see page 15).
5. NUMERIC BUTTONS
These buttons can be used for preset
tuning in TUNER mode. Preset tuning:
Press the TUNER button to change the
input function of the receiver to TUNER
and then select one of the 30 preset
locations. Selection of CD track number:
Press the CD button to change the input
function of the receiver to CD and press
the desired track number (1, 2, ... 98, 99),
then the CD player starts to play.
6. CD FUNCTION BUTTONS
For a CD PLAYER: DISC (DISC SKIP, this
is available for Harman Kardon CD
changers), (play), (pause), (stop), (back-
ward skip), (forward skip), A-B and INTRO
buttons are available. The A-B button is
used to repeat a specific passage.
7. CASSETTE DECK
FUNCTION
BUTTONS - For a cassette deck:
(pause/record), (stop), (record),
(reverse play), (forward play), (rewind),
(fast forward) buttons are available.
This will only work with some Harman
Kardon cassette decks.
8. DELAY TIME BUTTON
This button operates only in DOLBY
PRO LOGIC and HALL modes. In
these modes, the output signal from
the surround speakers is delayed
slightly from that of the front speakers.
Select appropriate delay time to
achieve the best surround-sound
effect. For Dolby Surround sound, we
recommend a 20ms delay. The time is
changed as below, when the button is
pressed in succession.
DOLBY PRO LOGIC
HALL MODE
9. INPUT FUNCTION
SELECTOR
Press the button to select the desired
input function. The available buttons
are CD, TUNER, TAPE 1, TAPE 2,
TV/AUX, VCR 1, VCR 2, and PHONO.
10. CENTER LEVEL
UP/DOWN BUTTONS
Use these buttons to adjust the sound
level of the center speaker to that of the
front speakers. These buttons work only
05 ms
10 ms
15 ms
20 ms
25 ms
30 ms
15 ms
20 ms
25 ms
30 ms
in DOLBY PRO LOGIC and DOLBY 3
STEREO mode. These buttons do not
work in PHANTOM.
11. CENTER MODE BUTTON
Selects the center mode (see page 14).
12. TEST TONE BUTTON
Generates test sounds in all channels
(Left, Center, Right and Surround) in
succession.
13. REAR LEVEL
UP/DOWN BUTTONS
These buttons operate only in DOLBY
PRO LOGIC and HALL mode. Use
these buttons to adjust the sound
level of the surround speakers. Set
the MASTER VOLUME control at the
desired level and press the up or
down button until you get the opti-
mum surround effect at your listening
position.
14. MASTER VOLUME
BUTTONS
Adjust the overall (front, center, and
rear) volume level.
15. DISPLAY BUTTON
Press once and the display dims,
press again and it turns off. Press a
third time and it goes on.
16. SLEEP BUTTON
Sets the receiver to automatically turn
off after 10, 20, 30, 60, or 90 minutes.
Each time the button is pressed, the
setting is advanced as below.
The display will dim when the sleep
function has been set.
17. MUTE BUTTON
Press this button to silence the
speakers temporarily. The volume
indicator blinks. Press again to
restore the same listening level as
before.
18. BATTERY
COMPARTMENT
This battery case is provided as the
power source for the commander. To
remove the cover, press it down with
your thumb and pull it toward the
back side. Two UM-3, size “AA” or R6
1.5V dry batteries are used. When
loading the batteries, make sure that
the polarity is correct. Remove the
batteries from the case if the remote
commander will not be used for a
long time.
10 min
20 min
30 min
60 min
90 min
OFF
JSR655om (a) qx 7/28/98 9:54 AM Page 19
