JBL EON Power10 Скачать руководство пользователя | Manualshive

Страница: 5 / 38

background image

15

7)

Remove the rear cover on the compression driver by removing the three(3) TORX head

screws using a #10 TORX driver. Do not discard the cover/screws.

8)

Remove the diaphragm assembly from the magnet structure or cover.

9)

Identify defect and record Q.A. code per JBL Professional Service Program manual.

10) Check the gap with a .040" gap gauge. Using compressed air and masking or “tuck”
tape, clean the gap thoroughly per JBL Professional rediaphragming procedures.

11) Lay the new diaphragm assembly into the magnetic gap and align the three screw
holes in the top plate with the three openings in the diaphragm assembly. ANY ORIENTA-
TION OF THE THREE HOLES IS ACCEPTABLE.

12) Be sure the diaphragm seats completely against the top plate within the guide pins.

13) Reinstall the rear cover over the diaphragm. Torgue these screws to 14 inch pounds.

14) Test the compression driver for rubs or buzzes using a 2 volt sine wave from 300Hz to
800Hz. If no buzzes are detected, then test at 2V from 1,500 Hz to 20 kHz for full range
operation and audio clarity. It will be necessary to lift the baffle to expose the horn so
listening tests can be performed accurately.

15) Reconnect the high frequency lead wires to the appropriate terminal on the compres-
sion driver. The terminals are polarized so they will fit only one way. Reconnect the trans-
former wires if they were disconnected in step 5 above.

16) Reinstall the rear enclosure on the front baffle (torque to 21 inch pounds) taking care to
ensure that the baffle gasket is not damaged. If the gasket is damaged, replace with PN#
3321167-001 (382-00036-00 for EON 10 and 10P). Reinstall the handle.

17) Perform a complete system test before returning the product to the customer.

A)

Initial Setup

Connect board under test to a +/– 15V power supply at the designated connector pins.
Connect Port-one generator (or a function generator) output A to XLR input connector.
Turn generator A off. Place S201 in “Mic” position.

1)

Power up board and verify that “Mic” LED, D202, lights.

Signal Input Assembly Trouble-shooting

EON Power15 and EON15P-1/230

«
...
3
4
5
6
7
...
»

Содержание EON Power10







































Отзывы:

Нет отзывов

Похожие инструкции для EON Power10

Бренд: Rain Bird Страницы: 2

Бренд: Harken Страницы: 4

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: TDR Страницы: 8

Бренд: Mach Страницы: 12

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

M-041 INDOOR CROSS

Бренд: Salter Страницы: 15

Бренд: Hammer Strength Страницы: 8

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

Бренд: Champlain Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды