ENGLISH
OPERATION MANUAL
JB SYSTEMS®
3/30
MINI KALEIDO
DESCRIPTION:
1.
Optical lens with manual focus adjustment
2.
Hanging bracket with 1 knob to fasten the unit and a mounting hole (M8) to fix a mounting hook like
CR16/30.
3.
Mains power cable
4.
Fuse holder
5.
Lamp compartment.
6.
Internal microphone
7.
Cooling fan
8.
switch for operation mode (auto or music)
LAMP (RE)PLACEMENT
In case of replacement of the lamp or maintenance, do not open the fixture within 10
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When
replacing parts, please only genuine spare parts.
Switch off the unit and unplug the mains cable.
Wait for about 10 minutes until the unit has been cooled down.
Unscrew the screw that closes the lamp compartment of the fixture.
On the inside you will see the lamp socket. Tear the lamp socket gently
out of the lamp compartment.
Unplug the old lamp. Hold the lamp socket while unplugging the lamp
instead of pulling the cable!
Hold the lamp socket while pressing the new lamp gently in the socket.
Attention!
Check the label on the backside of the device or see the
technical specifications in this manual to know which lamp should be used.
Never install lamps with a higher wattage! Lamps with higher wattage
generate temperatures the device was not designed for. If the device uses
a lamp transformer, it will burn due to current overload.
Don’t touch the bulb inside the reflector of the lamp with bare hands! This
drastically shortens the lifespan of the lamp. If you touched the lamp, clean
it with a cloth and a little denatured alcohol. Wipe the lamp off before
installing.
Put the new lamp back inside the unit. Be sure that the wires don’t touch
the lamp.
Close the lamp compartment with the screw.
Done!
ENGLISH
OPERATION MANUAL
JB SYSTEMS®
4/30
MINI KALEIDO
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed
at least 50cm
from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
Placed on the ground
Mounted on truss
Fixed to the wall
OPERATING INSTRUCTIONS
Once connected to the mains the device starts running.
The switch (8) can be used to control operation mode of the unit:
o
Switch set to “stop”:
kaleidoscopic effect is music controlled.
o
Switch set to “rotation”:
kaleidoscopic effect turns at a fixed speed.
Regular breaks during operation are essential to maximize the life of this device as it is not designed for
continual use.
Do not switch the unit on and off in short time intervals as this reduces the lamp life.
Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
Important:
Never look directly into the light source! Don’t use the effect in the presence of persons
suffering from epilepsy.
