JB Systems Lynx II LED, Руководство по эксплуатации

Страница: 5 / 34

ENGLISH OPERATION MANUAL
JB SYSTEMS ® 5/63 LYNX-II
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP button to select (normal) or (2 light show) mode.

Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
Sound Mode
The unit works to rhythm of the beat when used in standalone or master/slave mode

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP button to select or mode.

Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP button to select (blackout on) or (blackout off) mode.

Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
Pan Inversion
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP button to select (normal) or (pan inversion) mode.

Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
Tilt Inversion
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed

Press the MENU button until is shown on the display.

Press the ENTER button, the display starts blinking.

Use DOWN and UP buttons to select (normal) or (tilt inversion) mode.

Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
ENGLISH OPERATION MANUAL
JB SYSTEMS ® 6/63 LYNX-II
Led Display
Display on: display is always on.
Display off: display is off when not used.

Press the MENU button until the display shows .

Press the ENTER button, the display starts blinking.

Use DOWN and UP buttons to select (display always on) or (display off when not used).

Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again for about 2 seconds.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.

Press the MENU button until is shown on the display. (normal display)

Press the ENTER button to toggle between (normal display) and (display inversion).

After about 8 seconds your choice is automatically saved.
Focus Adjust
Used to help you adjusting the focus of the light beam and gobos.

Press the MENU button until is blinking on the display.

Press the ENTER button so the unit goes to the “tilt 90°” position.

Press the ENTER button so the unit goes to the “pan 0°” position.

Press the ENTER button so the unit goes to the “pan 90°” position.

Press the ENTER button so the unit goes to the “pan 180°” position.

Press the ENTER button so the unit goes to the “pan 270°” position.
In the Previous 5 steps you are able to adjust the focus with the UP/DOWN buttons on the unit (the display
shows the current focus status).
Attention: please note that you can only set an “average focus” for all 5 positions, so it is not possible to set
the focus perfectly sharp for all directions.

To go back to the functions press the MENU button.
Self-Test
Used to activate the internal “self-test” program which shows all possibilities of the unit.

Press the MENU button until is blinking on the display.

Press the ENTER button to start the internal self-test program.

To go back to the functions press the MENU button.
Temperature inside the unit
Used to show the temperature inside the unit

Press the MENU button until is blinking on the display.

Press the ENTER button and the temperature of unit will show on the display.

To go back to the functions press the MENU button again.
Fixture Hours
Used to show the number of working hours of the unit.

Press the MENU button until is blinking on the display.

Press the ENTER button to show the number of working hours in the display.

To go back to the functions press the MENU button.
Software version
Used to show the software version that is installed in the unit

Press the MENU button until is blinking on the display.

Press the ENTER button to show the software version on the display.

To go back to the functions press the MENU button.