Jazzy 1122 страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 29

background image

SECURE WHEELCHAIR TO WHEELCHAIR BASE

For the safety of wheelchair occupant the wheelchair must be fully constrained to
the wheelchair base.

To secure wheelchair:
1. Turn the power off.

2. Make sure Jazzy 1122 has the

power drive engaged (i.e. Not in
freewheel mode).

3. Fasten hook and loop fastener

strap to right I bar (on the
wheelchair) and the right U-
bracket (on wheelchair base)
located near the front wheels,
see figure 2.

4. Repeat step 3, for the left side.

5. Press release button on

retractable tie down strap to
release hook, figure 3.

Figure 1

Figure 2

Figure 3

«
...
6
7
8
9
10
...
»

Содержание 1122






























Отзывы:

Нет отзывов

Похожие инструкции для 1122

Kiddiepower (Sunny)

Бренд: Vermeiren Страницы: 14

trotter TR 1200

Бренд: Drive Medical Страницы: 6

Top End T-3 Tennis Adjustable

Бренд: Invacare Страницы: 64

Бренд: Glide Страницы: 31

Бренд: Motion Composites Страницы: 32

Бренд: ROHO Страницы: 2

Бренд: Coopers Страницы: 4

Бренд: Ti Lite Страницы: 109

Secura Premium 23546

Бренд: Maximex Страницы: 7

Бренд: Maximex Страницы: 6

R-Net BLUETOOTH

Бренд: Sunrise Medical Страницы: 3

Бренд: Falcon Страницы: 63

S-Ergo 105(KM-1500?3)

Бренд: Karman Healthcare Страницы: 32

Бренд: Pride Mobility Страницы: 3

Бренд: Pride Mobility Страницы: 32

Бренд: Future Mobility Healthcare Inc. Страницы: 27

Бренд: Sanction Industry Страницы: 2

GF0600059REVB06

Бренд: E&J Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды