Jazzy 1122 Скачать руководство пользователя | Manualshive

Страница: 3 / 29

background image

EMERGENCY KILL SWITCH

The emergency kill switch allows the aid control external control over the
trainer. By attaching the cord of the kill switch to the body of the attending
aid, they will be able to instantaneously slow down and stop the trainer in the
case of an emergency. This device cuts power to the motors when pulled.

To operate emergency kill switch:
1. Inserting: To insert kill switch,

hold three prong connector
with large prong on top and
two smaller prongs on bottom.

2. At an angle, push button on

trainer down with connector
and slide into place. See
Figure 1.

3. Disengaging: To stop trainer

in motion, pull on the tether
cord until connector un-
attaches from trainer. See
Figure 2.

4. When disengaged blinking red

light near keyed ignition will
be visible. See Figure 3.

WARNING:

Emergency Kill

Switch should always be
engaged unless in the case of
an emergency. Leave attached
when not in use, blinking red
indicator will tell blink with or
with out keyed ignition.

Figure 1

Figure 2

Figure 3

«
1
2
3
4
5
...
»

Содержание 1122






























Отзывы:

Нет отзывов

Похожие инструкции для 1122

Бренд: Otto Bock Страницы: 34

Бренд: Otto Bock Страницы: 36

Бренд: HD Rehab Страницы: 2

Бренд: R82 Страницы: 42

Бренд: panthera Страницы: 7

Бренд: panthera Страницы: 12

Бренд: panthera Страницы: 20

Бренд: R82 Страницы: 4

Бренд: Vermeiren Страницы: 120

ORTOPEDIA Solero Light 9.072

Бренд: Meyra Страницы: 52

Polaro II 1.745

Бренд: Meyra Страницы: 68

Бренд: Neatech Страницы: 85

Бренд: Sanction Industry Страницы: 4

Бренд: SPEX Страницы: 16

Бренд: SPEX Страницы: 16

Arm & Thigh Supports

Бренд: SPEX Страницы: 16

Бренд: JYD Imports Страницы: 13

Act Discontinued

Бренд: Etac Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды