Jaytech 1000N Скачать руководство пользователя

Страница: 17 / 19

- 15 -

Common Fault & Solutions

Fault

symptom

Fault

cause

Solution

Opener doesn

’

t operate

1. Power supply

2. Broken door spring

1. Check the power point is live.

2. Disengage the opener and try to lift the door manually, if it feels heavy call a

professional Technician.

Opener doesn

’

t work,

LED displays

“

”

Travel limits not set

Learn

“

”

and

“

DOWN

”

travel limits again (Pg8)

The door will open but

not close

Photo beam setting enabled with no

photo beams present or an obstruction

if photo beams are present.

Check photo beam settings are correct (Pg9)

If photo beams are installed, check for obstructions to the door travel.

Open and close action is

reversed

Reversed connection of the positive

and negative of motor wire to the

control board.

＊

Power off firstly, open the motor cover and reverse the positive and negative of

motor wire on the control board. Re-set the travel limits.

Door auto reverse to full

open before closing

completely

Safety reverse function. Obstruction or

door maintenance required

1. Check for any obstructions

2. Call a Professional Technician for maintenance

Transmitter doesn

’

t work

1. Flat battery

2. Antenna is loose or not well

extended

3. Signal interference

1. Replace battery

2. Extend the antenna on the opener

3. Eliminate signal interference (doorbell, baby monitor, alarm etc)

Can

’

t add new

transmitters

1. Memory is full

2. New transmitters are not compatible

with opener

Press and hold

“CODE” button

for more than 8 seconds until the LED flashes

“C”

2. Use only genuine Jaytech transmitters

LED displays

“

”

, opener

does not work

1. Motor plug wire is loose

2. Control board is damaged

1. Re-insert motor plug wire

2. Call professional Technician

LED displays

“

”

, opener

does not work

1. Motor is damaged

1. Call professional Technician

LED displays

“

”

after

opener operates several

centimeters only

1. Hall element wire plug is loose

between hall element and control

board.

2. Hall element or control board is

damaged

1. Check the wire plug

2. Check the hall element

3. Replace control board

Note: Only qualified Technicians should attempt repairs

Содержание 1000N




















Результаты поиска

Содержание 1000N

Отзывы:

Похожие инструкции для 1000N

Бренды по названию

Популярные бренды

Jaytech 1000N, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1000N

Отзывы:

Похожие инструкции для 1000N

Бренды по названию

Популярные бренды