![background image](http://html1.mh-extra.com/html/jayco/2009-melbourne/2009-melbourne_owners-manual_3468009060.webp)
SECTION 8
PLUMBING SYSTEM
56
8. Relieve the water pressure using the P&T
valve BEFORE removing the water heater
drain plug. Otherwise, if there is any water
pressure present the water will spray out
of the opening when the drain plug is
removed.
When you are finished draining the fresh
water system, reverse these steps and dump
the grey and black water holding tanks at an
appropriate facility or according to local public
codes.
U
TILITY
C
ENTER
The following information defines the function
of the utility center settings indicated on the
utility center label:
City Fixtures
- This setting allows you to
access water at all faucets using city water.
City Tank Fill
- This setting allows you to fill
your fresh water tank using city water.
Country Fill
- This setting allows you to fill
your fresh water tank (using the 12-volt water
pump) when you do not have access to city
water.
Normal
- If the RV is not connected to city
water, this setting allows you to pump water
from the fresh water tank to all faucets using
the 12-volt water pump.
Sanitize/Winterize Lines
– This setting
allows you to sanitize or winterize your fresh
water system.
Sanitize Tank
– This setting allows you to
sanitize the fresh water tank.
Fig. 8.5 Utility center label
The city water connection inlet is located on
an exterior sidewall. We recommend that you
use a non-toxic drinking water hose dedicated
only to supplying the RV with fresh water (to
reduce the chance of contamination, prevent
the non-toxic drinking water hose from coming
into contact with the ground). Install the city
water connection inlet cap when the fresh
water connection is not being used. Do not
remove the following label from your RV:
Fig. 8.6 Potable water only label
The fresh water connection should be
unplugged (i.e., the non-toxic drinking
water hose disconnected) when the RV is
unattended for any amount of time. If
something would happen to the water
system, this may help limit water damage
to a smaller area.
U
SING
T
HE
C
ITY
F
ILL
Use this setting if you are at a campground or
other facility where the RV can be hooked up
to an external water source.
1. If needed, sanitize the water system prior
to travel.
2. Move the “water heater bypass valve” to
the NORMAL position.
3. Remove the city water connection inlet
cap and attach a non-toxic drinking water
hose to the city water connection inlet.
4. Place the utility center valves in the “City
Fixtures” position.
5. Turn ON the water at the external water
source.
6. Enter the RV and open the cold water
supply faucets to bleed air from the water
lines. When the water lines are nearly full,
Содержание 2009 Melbourne
