background image

Operator’s Manual 

 
ATTACHING BUCKET OR OTHER ATTACHMENT 
LOADERS WITH SKID-STEER TOOL CARRIER 
 
 

 

 

WARNING: Use only buckets and attachments compatible with SAE J2513 

 

 

 

standard. Use of other attachments does not guarantee safe connection of the 

 

 

 

bucket with the loader. Serious injury or death may result. If unsure about the 

 

 

 

attachment origin, contact a TYM dealer and ask for assistance. 

 

 

 

CAUTION: Except when detaching or attaching bucket or other attachment, keep 

 

 

 

the bucket latching handles in the LOCKED POSITION (handles in hor. position) 

   CAUTION: 

To 

maintain 

proper 

function 

of the quick attach system, inspect the 

   latching 

handles, 

lockpins, 

attachment coupler and attachment flange for damge 

 

 

 

before attaching the bucket. If damage exists, replace component immediately. 

 

 

 

CAUTION: Make sure all parts of the quick attach system are clean before 

 

 

 

attaching the bucket.  Only clean components will function safely. 

 

1.

 

Move latching handles to the UNLOCKED 
position (UP). 

 
 
 
 
 

2.

 

Have the attachment coupler slightly tilted forward 
Drive tractor centrally to the bucket.  The top of the  
attachment coupler must be aligned with the  
attachment flange on the bucket. 
Lift loader a few inches and roll the bucket back. 

 
 
 
 

3.

 

Move latching handles into LOCKED position 
(DOWN – handles must be horizontal). 
The lockpoins must be extended and secured  
into the retaining slots on the bucket. 
CAUTION: Before leaving the seat, stop engine 
and engage hand brake. 

 
 
 
 
 
 
 
 
 
 

4.

 

Check proper latching by lowering loader and pushing loader bucket against ground by moving 
joystick forward. (Improperly attached bucket would get loose while pushed against ground). Bucket 
must be level (in horizontal position) during this check. 

T50SS/T50HLSS 

    6 

Содержание TRAC-LIFT T50HLSS












Отзывы: