background image

User Manual Javo Plus en Plus Extra Potmachine 

Version 2015-1 

 19 

6

 

Operation 

Follow all instructions described in this manual, in particular chapter safety.  

 

Keep hands, hair, loose clothing and / or jewelry away from moving parts of the machine. Wear appropriate 

clothing without loose parts. Wear non-slip work shoes.  

As long as the machine is on, no connection or safety devices may be removed. The machine may only be 

used when all protective devices and safety-related facilities are available and ready for use. 

 

If a machine part is damaged or not working in the prescribed manner, work must be interrupted 

immediately. Resumption allowed only when the machine part is repaired or replaced and checked. Consult 

your dealer if the machine is not functioning properly.   

6.1

 

Start 

Start procedure: 

1.

 

Turn on the main power at the electrical cabinet.  

a.

 

Stop/ Error indication lamp will lit. 

2.

 

Turn on the drill, potttrack and elevator with switches at the 

electrical cabinet. 

 

 

 

 

 

 

 

 

 

3.

 

Press the blue reset button (C). 

4.

 

Press the green button (B) on the control panel to start the 

machine. 

 

6.2

 

Stop 

Stop procedure: 

1.

 

Press the red stop button (A) on the control panel. 

a.

 

Stop/ Error indication lamp will lit. 

6.3

 

 Emergency stop 

Emergency stop procedure: 

1.

 

Press the red emergency stop button on the machine to activate the emergency 

stop. 

 

Restart after emergency stop procedure: 

1.

 

Ensure that the cause of the emergency is resolved.  

2.

 

Close all doors and covers.  

3.

 

Pull the red emergency stop button to reset.  

4.

 

Press the reset button.  

5.

 

Press the green button on the control panel to start the machine. 

 
 

 

Содержание Plus



























Отзывы: