Javelin RTR5024 Скачать руководство пользователя страница 41

Страница: 41 / 44

TROUBLESHOOTING GUIDE

If the unit does not operate normally when you follow the instructions indicated in the manual, please refer to the table
below.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

No power

The power cord is not connected

Connect the power cord

No image displayed on
the monitor TV

The connections are not correct

Check that all connections are correct

The power to the camera and/or monitor TV
is not turned on

Turn all connected devices power on

The buttons do not
respond

A cassette tape is not loaded

Load a cassette and turn the power on

All functions are suspended due to
condensation

Wait for the “

” indicator to go off

Alarm recording

Wait for the alarm recording to end

The security lock is engaged

Cancel the security lock

Recording is not
possible (the tape is
ejected)

The loaded cassette has no
erasure-prevention tab

Load a cassette tape with
erasure-prevention tab or cover the tab hole
with adhesive tape

Autorepeat recording is
not possible

“AL” is displayed on the digital display

Display (ALARM TIME) menu, then press
the MENU RESET button to turn off the “AL”
indicator

Timer recording is not
possible

The date and time are not set correctly

Set the date and time correctly

The unit is not set to timer recording
stand-by mode

Press the TIMER button to display “

” on

the digital display

“N” is selected for the timer recordings

Be sure to select “Y” for the programmed
timer recordings

Alarm recording is not
possible

“OFF” is displayed on the digital display

Press the EJECT, STOP, FF, REW or
PLAY button to turn the indicator off

Noise in the playback
picture

The video heads need cleaning

Clean the video heads

The date and time are
not recorded

The ON SCREEN switch is set to the “OFF”
position

Set the ON SCREEN switch to the “ON”
position

The cassette tape
cannot be ejected

Problem with the system

Unplug the power cord then plug it back in

The cassette is ejected
a few seconds after it
has been inserted

The tape is not threaded correctly

Try inserting the cassette one more time or
using a new cassette. If it is ejected again,
please consult your dealer.

After a Power Failure

If after a power failure the recording speed is reset to
8-hour mode, it is due to insufficient backup battery
charge. This is not a malfunction.

System Down

If the unit does not function at all, try the following.

Unplug the power cord then plug it back in.

Reset the memory. (Press the ALL RESET button.
Under normal conditions, do not touch the ALL
RESET button.)

If the problem is not corrected after performing steps

and

a few times, consult your dealer.

RC4QR/NAJV, NAJV2 (RTR5024, RTR5168 GB) Wed. June, 07/2000

English

Содержание RTR5024













































Результаты поиска

Содержание RTR5024

Отзывы:

Похожие инструкции для RTR5024

Бренды по названию

Популярные бренды

Javelin RTR5024, Инструкция по эксплуатации

Результаты поиска

Содержание RTR5024

Отзывы:

Похожие инструкции для RTR5024

Бренды по названию

Популярные бренды