Javelin RTR5024 Скачать руководство пользователя страница 38

Страница: 38 / 44

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold
separately) to control remotely the VCR.

NOTE:

The functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a
remote controller with a circuit such as indicated below, to
the REMOTE jack.

NOTES:

Use a 3.5 mm mini-jack type plug.

The connection should be done using a shielded cable
no more than 5 meters long.

The functions not available on the VCR will not operate.

Remote control setting

The remote control switch 7 can be set to either eject the
tape or access the menus.

Press the MENU button until the (SET UP 1) menu is
displayed.

@@@@@@@<SET@UP@1>

öDAYLIGHT@SET@@@@@USE

@@@@@@@@WEEK@MONTH@TIME

@ON@@@1ST-SUN@@04@02:00

@OFF@@LST-SUN@@10@02:00

öOUTPUT@@@@@@@@SERIES

öCLOCK@SET

@10-15-01@MON@@15:20:00

öREMOTE@@@@@@@@EJECT

öLANGUAGE-LANGUE-IDIOMA

@@@ENGLISH

Press the

(or

) button, until the “REMOTE” setting

is flashing.

Press the

(or

) button, to select the desired

switch mode.

EJECT . . . . . Switch 7 will eject the tape.

MENU . . . . . Switch 7 will display the menu.

Press the SEARCH button to save the setting.

SW0: EJECT

R0 1.2K

Remote control circuit

The resistance tolerance is
2% or less.

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: REV

SW1: STOP

SW9: REC/PLAY SPEED

SW10: REC/PLAY SPEED

SW11: SHIFT

]

SW12: SHIFT

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R1 0.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

RC4QR/NAJV, NAJV2 (RTR5024, RTR5168 GB) Wed. June, 07/2000

English

Содержание RTR5024













































Результаты поиска

Содержание RTR5024

Отзывы:

Похожие инструкции для RTR5024

Бренды по названию

Популярные бренды

Javelin RTR5024, Инструкция по эксплуатации

Результаты поиска

Содержание RTR5024

Отзывы:

Похожие инструкции для RTR5024

Бренды по названию

Популярные бренды