specifications, installation
and operation instructions
Models EBS--1
page 7 of 12
JARVIS
6205012:.
®
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL.
TEL. 860--347--7271 FAX. 860--347--6978 WWW. j
arvisproducts.com
SPECIFICATIONS
Models EBS--1
Motor Power
1.9 hp
1400 W
Operating Voltages
42, 115, 230, 400, 415 V, 3 phase, 50 Hz
220, 240, 380, 480 575 V, 3 phase, 60 Hz
Blade Lengths EBS--1
9.5 in
241 mm
10.5 in
267 mm
11.5 in
292 mm
13.0 in
330 mm
Blade Lengths EBS--1--H
15.8 in
400 mm
Blade Lengths EBS--1--HS
21.9 in
556 mm
Control Handle
Single / Electric
Cut Speed
at 60 Hz
750 ft/min
229 m/min
at 50 Hz
625 ft/min
191 m/min
Cutting Cycle Time
4 sec
Overall Length (w/o blade)
24 in
610 mm
Overall Length (9.5 in blade)
28 in
711 mm
Weight
53 lbs
24 kg
INSTALLATION INSTRUCTIONS
Refer to Figure A on page 4 for referenced items.
IMPORTANT: ALWAYS DISCONNECT THE ELEC-
TRIC POWER SUPPLY IN ACCORDANCE WITH
OSHA’S
LOCKOUT/TAGOUT
PROCEDURES
(29CFR 1910.147) BEFORE PERFORMING ANY
MAINTENANCE OR REPAIRS.
ALL WIRING MUST BE DONE IN ACCORDANCE
WITH NATIONAL, STATE AND LOCAL ELEC-
TRICAL CODES.
1 Install the Model EBS--1 saw above the work station
from a balancer.
Jarvis
part number 4042034 is
available.
1.1 The saw should have sufficient travel to allow
the operator to reach the entire work area.
2 Position power cord for either top exit or rear exit as
desired.
2.1 Unplug the tool.
2.2 Remove four (4) screws (items 53 or 69), electri-
cal box cover (item 56 or 68) and gasket (item 58
or 67).
2.3 Disconnect power cord (item 54 or 71) from
switch (item 50 or 73).
2.4 Remove two (2) locking nuts (item 57), cord
connector (item 55 or 70) and plug (item 60 or
76).
2.5 Swap positions of cord connector and plug. Re--
tighten nuts.
2.6 Reconnect power cord (item 54 or 71) to switch.
2.7 Check motor rotation. Motor rotation must fol-
low direction of arrow shown in
Figure 1.
Crank (item 33) will unscrew if motor direction is wrong.
Figure 1
Keep
hands
cl
ear
.
Motor rotation must
follow direction of
arrow.
Motor Cover
2.8 Reinstall gasket (item 58 or 67), cover (item 56
or 68) and four (4) screws (items 53 or 69).
3 Connect the tool to the appropriately fused electric
outlet.
OPERATION INSTRUCTIONS
1 Prior to use or daily perform the following tests:
1.1 Make sure that the saw moves freely on the ba-
lancer.
1.2 Make sure the control trigger is working correct-
ly.
Depress
the trigger and the tool should start.
Release
the trigger and the tool should stop.
If
the tool malfunctions, remove it from service
and report the problem to your supervisor im-
mediately
.
Always use two hands when starting and
stopping the tool.
2 Make the cut:
2.1 Insert the saw blade into the cut made in a pre-
vious operation.
2.1.1 The front end of the saw should be tipped up
at approximately a 30 degree angle.
