Japan Radio Co. JLR-7900 Скачать руководство пользователя | Manualshive

Страница: 5 / 184

background image

iii

Precautions Upon the Operation

WARNING

Do not disassemble or modify the equipment. Doing so may result in fire,
electric shock, or equipment failure.

Do not allow the display to become wet. Doing so may result in fire, electric
shock, or equipment failure.

Operate the equipment only at the indicated voltage. Failure to do so may
result in fire, electric shock, or equipment failure.

Do not perform internal inspections or modifications of the equipment.
Inspection or modification by unauthorized personnel may result in fire, electric
shock, or equipment failure. Please consult with JRC or an affiliate to perform
internal inspections or repair.

When disposing of the used lithium battery, place insulating tape over the
battery terminals, or otherwise insulate the battery. Failure to do so may result
in heating, explosion, or fire due to a shorted battery.

Install this unit at least 1 m away from any magnetic compasses. Installation
near a magnetic compass may result in interference with the magnetic
compass, and may result in an accident.

Do not perform internal inspections or modifications of the equipment.
Inspection or modification by unauthorized personnel may result in fire,
electric shock, or equipment failure. Please consult with JRC or an affiliate
to perform internal inspections or repair.

«
...
3
4
5
6
7
...
»

Содержание JLR-7900

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JLR-7900

Бренд: Hama Страницы: 12

Бренд: TBIT Страницы: 3

Бренд: Origin Страницы: 17

Apollo SL50 GPS

Бренд: II Morrow Inc. Страницы: 62

Blackbird Asset Tracker

Бренд: Blackbird Technologies Страницы: 12

RoyalTek BV-3200

Бренд: RTK Страницы: 34

Бренд: AOVX Страницы: 14

860 PRO PersonalMate

Бренд: Transystem Страницы: 28

Super Guard PT-2

Бренд: Yield Technology Страницы: 11

Бренд: Expresso Satellite Navigation Страницы: 19

Бренд: XAiOX Страницы: 14

Бренд: AIRIS Страницы: 5

Бренд: Dyegoo Страницы: 13

Бренд: DCS Страницы: 27

Бренд: Xexun Страницы: 14

Бренд: Safety Track Страницы: 7

Бренд: Bad Elf Страницы: 20

Бренд: TICATAG Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды