Janome MC15000 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

Janome MC15000 Скачать руководство пользователя страница 18

16

200 g pressure

5 mm

Setscrew

Replacing electronic components

Driving motor

To remove:
1. Remove the belt cover, the top cover, the front cover and

auxiliary power supply unit case

(see page 1, 2, 5 and 13).

2. Disconnect the connector of the foot control from the

printed circuti board A (see page 7).

3. Disconnect the connector A from the power supply unit.

Remove the setscrew C and the ground wire.

Remove the setscrews B (3 pcs.) and the case D.

D

B

C

B

A

E

F

F

4. Disconnect the driving motor connecter from the printed

circuit board A.

5. Remove the motor belt E.
6. Remove the setscrews F (2 pcs), and the driving motor.

To attach:
1. Attach the driving motor.

Tighten the setscrews F temporarily.

2. Adjust the motor belt deflection to about 5 mm by

pressing the middle of the motor belt with your finger with

approximately 200 grams of pressure.

3. Tighten the setscrews F securely.
4. Attach the driving motor connector and the foot control

connector to the printed circuit board A.

5. Attach the case D with the setscrews B.

Be careful not to bind the cords with the cover.

Attach the connector A to the power supply unit.

Attach the ground wire with the setscrew C.

B

«
...
16
17
18
19
20
...
»

Содержание MC15000

























































Отзывы:

Нет отзывов