25
EN
EN
24
G. INSTALLING THE iMATRIX ON THE COMFY Base
Recline the backrest to the R4 position (baby sitting up).
2
.a
Position the baby carrier so that it is fastened with the Pro-Fix anchors
intended for the iMATRIX(7).
2
.b
Check that both sides are firmly anchored in place, your IMATRIX will
be correctly locked into place when you hear the click and sea a green
strip on the Pro-Fix lever (situated on the handwheel of the handle).
2
.c
Set the IMATRIX handle to the AUTO position, make sure that it is locked
into place, and the car symbol is fully displayed.
2
.d
To do this, simul-
taneously press the release buttons found on both sides, and turn it
forwards as far as possible.
2
.e
Press the whole unit so it is fitted firmly against the backrest of the
vehicle seat.
2
.f
WARNING
: Your COMFY Base can be used with two different
baby carrier models, make sure you insert the Pro-fix of your
iMATRIX into the correct position for this model, you will find
the instructions on the platform. Once anchored, the exterior
surface of the safety seat backrest should be touching the
fastening bar (9).
2
.f
H. DETACHING THE iMATRIX FROM THE COMFY Base
Turn the IMATRIX handle to the Carry position.
Pull the release levers on both sides of the handle to release the Pro-
Fix anchors and lift the infant car seat up.
2
.g
To remove the platform:
Release the ISOfix anchors by turning the buttons (4), the ISOfix anchor signal
will turn red.
3
The ISOfix anchors can be concealed inside the platform
4
I. PLACING THE BABY IN THE iMATRIX
FOR CHILDREN FROM 40 TO 60CM
5
.a
1- Headrest position C1
2- Cushion insert
3- Handle position 3 CAR
FOR CHILDREN FROM 60 TO 83CM
5
.
b
1- Headrest position C2
2- NO cushion insert
3- Handle position 3 CAR
!
F. INSTALLING THE COMFY Base IN YOUR CAR
Not all systems are the same, therefore we advise you to test your COMFY Base in the
car where it is going to be installed. To install the platform, read your vehicle instruction
manual, it will tell you which seats are compatible with the platform. The COMFY Base is
compatible with the ISOfix category D.
The anti-rotation leg (1) is an important safety feature, fit it correctly so it is supported
by the floor of the vehicle. If the leg support surface is not the actual vehicle chassis
(luggage compartment for example) do not install the platform on this seat. To do this,
follow the steps below:
Position the base on the seat with the anti-rotation leg (1) and the fastening bar (9)
unfolded. Extend the leg with the help of the upper adjustment button (5a), until the
window indicator shows OK and the button changes to green.
1
.a
Extract the ISOfix anchors (2) by turning the handle (4) on the side of the platform.
1
.b
Guide both anchors (2) towards the ISOfix connectors of your vehicle and press until
both sides are locked. Two green signals on the release buttons (3) will show you that
they are correctly anchored.
If one or both of the signals are red, repeat this step.
1
.c
Adjust the height of the leg (1) so that it rests on the floor of the
vehicle, the indicator on the base of the leg (10) and the indicator on the leg adjustment
button (5b) will turn green.
1
.d
The COMFY base can be reclined to improve the angle of rest for the baby. Turn the
handwheel (3) to adjust the angle.
1
.e
R4
R3
R2
R1
1
2
3
IM 1893.05 iMATRIX ES-EN-FR-DE-IT-PT-NL ins.indd 24-25
14/6/21 19:59
