Jandy 200, Инструкция по установке и эксплуатации

Страница: 22 / 48

Page 22
ENGLISH
Jandy
®
Pro Series, JXi
™
Gas-Fired Pool & Spa Heater
|
Installation & Operation Manual
Part Number: H0402900 REV A (wiring diag) ; H0416500 REV A (note)
Description: JXi Heater - Wiring Diagram Label for inside front panel
Size: H0402900 REV A: 6.25 x 7 inches ; h0416500 REV A: 2.5 x 2.75
Color: Black
die line, does not print
L1
F1
ACN1
ACH1
L2
F2
G
R
BK
240 VAC
HEATER
POWER
SUPPLY
BLOWER
MOTOR
BK
R
Y
BL
W
IGNITION CONTROL
F1 F2 24
VAC
FV+ FV-
IGN
120 L1 L2
IGN
FS
W GND VAL
BK
W
BK
BL R
GY BK
24 VAC
R
Y
HOT SURFACE
IGNITER
W
GY
W
TRANSFORMER
WATER
TEMP
GAS
VALVE
USER
INTERFACE1
BK O BL R
HIPRESS/
HILIMIT
LOPRESS/
FUSELINK
WATER
PRESS
REMOTE
SPA POOL COM
REV
VALVE
24VAC
PUMP
COMP/
IGN
FAN/
LOUVER
UNIVERSAL
CONTROLLER
POWER INTERFACE
UNIVERSAL
CONTROLLER
USER INTERFACE
BYPASS
CONTROLLER
SWITCH
POWER
INTERFACE
BK O BL R
AIR FLOW
SWITCH
GAS VALVE
WATER
TEMP
SENSOR
BL
W
BK
TO PUMP STARTER
CONTACTS (IF USED)
TO COMBUSTION
AIR LOUVER STARTER
(IF USED)
W
FUSE
R
R
Y
Y
O
BK/Y
BK/Y
O
Y/BK O BR Y
BR Y
R
BL
BK
BK
BK
W
BK
BL
BR
Y
W W
W
BL
BL
BL/W
O V GY
BK
BK
PSW
Y/BK
C
NO
NC
Y/BK
COIL/AIR
TEMP J3 CONNEC
TOR
Factory Wired 24V
Factory Wired 120V/240V
BK - BLACK
BK/Y - BLACK WITH YELLOW TRACE
BL - BLUE
BR - BROWN
G - GREEN
GY - GRAY
O - ORANGE
R - RED
V - VIOLET
W - WHITE
Y - YELLOW
Y/BK - YELLOW WITH BLACK TRACE
H0402900 Rev
D
120 VAC
HEATER
POWER
SUPPLY
Alternate 120V Wiring*
G
R
BK
NEUTRAL
HOT
Voltage Selector Card Must Be Rotated.
LIMIT
SWITCH
57˚C
(135˚F)
LIMIT
SWITCH
66˚C
(150˚F)
WATER
PRESS
SWITCH
VENT
TEMPERATURE
LIMIT
240˚C
(464˚F)
6.25 x 7.0
NOTE: SI L’UN QUELQONQUE DES FILS
D’ORIGINE FOUMIS AVEC LE
CHAUFFE-PISCINE DOIT ÊTRE REMPLACÉ,
UN FIL POUR APPAREILS ÉLECTRIQUES À
TOLERANCE NOMINALE DE 105 °C DOIT
ÊTRE EMPLOYÉ. SI LE FIL PORTE LE
SYMBOLE ---------, LE REMPLACER
UNIQUEMENT PAR UN FIL POUR
APPAREILS ÉLECTRIQUES À TOLERANCE
NOMINALE DE 200°C.
NOTE: IF ANY OF THE ORIGINAL WIRE AS
SUPPLIED WITH THE HEATER MUST BE
REPLACED, APPLIANCE WIRING MATERIAL
RATED FOR 105°C MUST BE USED. WHERE
MARKED THUS - - - - - , APPLIANCE WIRING
MATERIAL RATED FOR 200°C MUST BE USED.
H0416500 Rev
B
die line, does not print
2.5 x 2.75
OPTIONAL
BYPASS
ACTUATOR
BK/Y
CIRCUIT BOARD
FOR
OPTIONAL
BYPASS
V
V
Figure 19. JXi Connections/ Schematic Wiring Diagram