J&J Amusements Can-Am Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 272

J&J Amusements Can-Am Скачать руководство пользователя страница 93

6-7

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

Use a 9/16” offset-ratcheting-box wrench and
loosen the engine-mount lock-down bolts.
Use a 3/4” socket and turn the belt adjuster bolt
clockwise until the engine is all the way forward
and the drive belt is loose.

NOTE:
Before the engine can be moved, the grabber plate
must be loosened (see page 8-3).

Remove the drive belt.

NOTE: Do not use a crowbar to pry the belt. It
should slip off.

STANDARD BELT TENSIONING PROCEDURE

Adjust the drive belt tension by turning the motor
adjusting bolt clockwise (to loosen belt tension) and
counterclockwise (to tighten belt tension) by using
a 3/4” socket with an extension.

NOTE:
Make sure the drive belt is tensioned to prevent
jumping of the teeth under the most severe load
conditions that the drive belt will encounter during
operation.

Tighten the engine-mount lock-down bolts and
make sure the drive belt is properly aligned.

Forward

Adjusting bolt

STANDARD BELT ALIGNMENT PROCEDURE

A straight edge can be used to aid in belt alignment
during reassembly. Place a straight edge along the
axle pulley and hold the straight edge firmly against
both sides of the pulley. The straight edge should line
up just inside the flange of the engine pulley.

GX240-270 COOL-TEK CLUTCH KIT
#1-00-K0001CT
#1-00-K0002CT

ENDURANCE CL

UTCH PLA

TES

TM

«
...
91
92
93
94
95
...
»

Содержание Can-Am

















































































































































































































































































Отзывы:

Нет отзывов