manualshive.com logo in svg

J&J Amusements Can-Am, Руководство по обслуживанию, Страница: 111 / 272

Поделиться
Скачать
J&J Amusements Can-Am Скачать руководство пользователя страница 111

6-25

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

The axle has two 1-1/4” (2 piece) split collars.
One on the inside of the drive axle bearing and one 
on the inside of the floater hub axle bearing. 
The split collars are installed to keep the axle from 
shifting during side impacts. 

Apply blue Loctite on each of the split collar Allen 
bolts.
Loosely install the split collar on the axle and slide 
it up against the inside of the drive bearing.
Evenly tighten the Allen bolts by using a 3/16” 
T-handle Allen wrench.

Install the split collar on the floater-side axle 
bearing in the same order as performed on the 
drive-side axle bearing.

Rotate the axle so the Allen bolts are facing down. 
Use the 3/16” T-handle Allen wrench between the 
frame and axle bearing; evenly tighten the Allen 
bolts.

SPLIT COLLARS HELP KEEP YOUR AXLE FROM SHIFTING.

Split collar, 1 1/4” (2 piece) #1-60-0065

Содержание Can-Am

















































































































































































































































































Отзывы:

Нет отзывов