manualshive.com logo in svg

J&J Amusements Can-Am, Руководство по обслуживанию, Страница: 131 / 272

Поделиться
Скачать
J&J Amusements Can-Am Скачать руководство пользователя страница 131

7-17

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

Attach a CLEAR plastic hose (1/8ID) to the bleed 
valve on the caliper and run the other end of the 
hose into a container.
The overflow hose should be submerged in fluid.  
This prevents any chance of inadvertently sucking 
air back into system.

                           Remove the master cylinder cap.

PUMP AND BLEED
You will need a second person to aid in pumping 
and holding the brake pedal. The helper pumping 
the pedal must use slow but firm pedal movements. 
Pump the pedal until it is solid, then stop and hold.  
Open the bleeder valve; the pedal will move to the  
end of the stroke as the cylinder pushes the air/fluid 
through the system. DO NOT RELEASE THE PEDAL. 
Hold the pedal all the way down until the bleeder 
valve is closed, then release.  
Slowly repeat the pump-and-bleed process until 
clear fluid flows out of the bleeder valve without air 
bubbles.
Monitor the fluid level in the master cylinder, 
making sure the level never drops below 1/3  full. 

NOTE: Never put drained/used brake fluid back into 
the master cylinder.

NOTE: Always proceed in a slow and deliberate 
manner.

<WARNING>
Bleed air whenever the brake pedal action feels soft 
or spongy, after brake fluid is changed, or whenever 
a brake fitting has been loosened for any reason.

 BLEEDING   THE BRAKE SYSTEM (Manual Method)

REPLACEMENT BRAKE PADS!

Brake pads # 010820A
Retainer clip # 010942

NOTE: Master cylinder cap must 
be removed when performing this 
procedure. 

Содержание Can-Am

















































































































































































































































































Отзывы:

Нет отзывов