JAI TMC-775 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 82

background image

TMC-775/TMC-773

16

Hardware Installation

Figure 3.

Back Focus Set-Screw Locations

2.2.5

Auto-Iris Lens Setup

Auto-iris lenses with full video input can be used with the JAI, Inc. TMC-775 and TMC-773.

Note: Make sure that the power is removed from the camera before connecting or disconnecting the auto-iris

lens. There is a small chance that damage could occur to the auto-iris lens by plugging or unplugging it
while the camera is powered up.

Power down the camera before installing the auto-iris lens. To install the auto-iris lens in a JAI, Inc. camera, wire
the signal on the lens into the 1 V peak-to-peak video output (pin 11) on the camera. 12 volts DC is available on
pin 3.

Point the camera at a light area and then quickly towards a darker area. If everything is working properly, the iris
should adjust for the light change.

2.2.6

Monitor Display Mode

For monitoring real time video, connect the video output to an NTSC video monitor or other device.

2.2.7

Connectors and Cables

15-pin connector and cable: Standard cable is 15P-02-9P and 15P-02-9P-FULL.

Figure 4.

15P-02-9P Cable

«
...
14
15
16
17
18
...
»

Содержание TMC-775



















































































Отзывы:

Нет отзывов

Похожие инструкции для TMC-775

Бренд: Canon Страницы: 54

Бренд: Canon Страницы: 54

Бренд: U-Prox Страницы: 3

Бренд: Zavio Страницы: 16

Бренд: D-MAX Страницы: 8

D-AIR STREET SMART CHEST Series

Бренд: DAINESE Страницы: 188

Бренд: Idis Страницы: 20

Бренд: Bose Sicilia Страницы: 24

Бренд: Y-cam Страницы: 12

Бренд: Dante Страницы: 7

Бренд: Yolink Страницы: 30

Бренд: Pyronix Страницы: 2

Бренд: Grundig Страницы: 98

Бренд: KaiCong Страницы: 44

Бренд: PNI Страницы: 83

iBORESCOPE DCiS1

Бренд: General tools Страницы: 20

Бренд: SAINT-GOBAIN Страницы: 18

Бренд: V-Tec Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды