JAI TMC-775 Скачать руководство пользователя страница 20

Страница: 20 / 82

TMC-775/TMC-773

Software Introduction & Installation

Figure 9.

Vertical timing details for interlaced. NTSC

3.2.2

Integrate Mode

The standard factory setting for the TMC-775/TMC-773 camera is FIELD MODE.

An External Integrate mode is located on pin 12 of the 15 pin connector. This allows frames to continually
integrate until this input pin is released. This is normally high or open. Holding the input “low” starts the integration.

To use this mode:

Input:

Ext. signal to pin 12 on 15 pin connector.
Set MFI mode: “VD mode”
Set MFI Termination: “Hi Z”

3.2.3

Vertical Mode

The standard factory setting for the TMC-775/TMC-773 camera is FIELD MODE.

In Field Mode, two horizontal rows are scanned together, changing the pair at each interlace scan.

3.2.4

External Trig

The External Trig functions are not supported during continuous operation.

Содержание TMC-775



















































































Результаты поиска

Содержание TMC-775

Отзывы:

Похожие инструкции для TMC-775

Бренды по названию

Популярные бренды

JAI TMC-775, Руководство пользователя

Результаты поиска

Содержание TMC-775

Отзывы:

Похожие инструкции для TMC-775

Бренды по названию

Популярные бренды