JAI RM/TM-1327GE Series Скачать руководство пользователя страница 34

Страница: 34 / 62

RM/TM-1327GE Series

Configuring the Camera

GainRaw:

controls the Gain value.

VTop:

affects digital gain. Decreasing the value results in brighter image.

VBottom:

adjusts the black level of the image. Increasing the value will increase the black level and darken

the image. Available only when AutoBlackLevel is disabled.

AutoBlackLevel:

adds tiny positive or negative voltages to both Vtop and Vbottom to compensate black level

changes due to temperature. Enabling this will disable VBottom adjustment.

5.3

Image Size Controls

These controls allow you to make adjustment to the image’s size and scan mode

Figure 12.

ImageSizeControl category

SensorDigitizationTaps:

the camera is a single tap camera and it uses one channel to read out images from the

image sensor.

WidthMax:

shows the current valid maximum value for Width.

HeightMax:

shows the current valid maximum value for Height.

Width:

sets the width of the output image. When ScanMode is changed it is necessary to set this value to equal

to or less than WidthMax.

Height:

sets the height of the output image. When ScanMode is changed it is necessary to set this value to

equal to or less than HeightMax.

OffsetX:

specify the offset from the left edge of the image captured by the sensor to be sent out of the

camera. Width must be set lower than WidthMax before this value can be increased.

OffsetY:

specify the offset from the top of the image captured by the sensor to be sent out of the camera.

Height must be set lower than HeightMax before this value can be increased.

•

Offset Example:

•

ScanMode is set to A_1392x1040

•

Width to 600 and Height to 100.

Содержание RM/TM-1327GE Series































































Результаты поиска

Содержание RM/TM-1327GE Series

Отзывы:

Похожие инструкции для RM/TM-1327GE Series

Бренды по названию

Популярные бренды

JAI RM/TM-1327GE Series, Руководство пользователя

Результаты поиска

Содержание RM/TM-1327GE Series

Отзывы:

Похожие инструкции для RM/TM-1327GE Series

Бренды по названию

Популярные бренды