JAI GO-2400C-PMCL Скачать руководство пользователя страница 40

Страница: 40 / 100

GO-2400M-PMCL / GO-2400C-PMCL

For color

Master

Gain

setting

value

Gain

amplification

Gain setting

value (scaling)

Gain adjustment range (Bayer color)

X89.12

X16

X7.15

X5.62

X0.45

1600

37876 (X5.62)

0 (X1)

–4533 (X0.45)

R&B

Red

Blue

39dB

-7dB

0dB

24dB

15dB

0dB

–7dB

15dB

0dB

–7dB

15dB

37876 (X5.62)

0 (X1)

–4533 (X0.45)

LUT (Lookup Table)

The LUT function is used to generate a non-linear mapping between signal values captured on the
sensor and those that are output from the camera. You can specify the output curve using 256 setting
points (indexes) on the GO-2400M/C-PMCL.

■

To use the LUT function

Configure the settings as follows.

Item

Setting value / selectable

range

Description

JAI LUT Mode

LUT

Use LUT.

LUT Selector

R, G, B

Select the LUT channel to control.

LUT Index

GO-2400M-PMCL: 0 to 255

GO-2400C-PMCL: 0 to 255

Select the LUT index to configure. Indexes represent the

setting points, and values from the lowest point (Index 0) to

the highest point (Index 15) are represented. On the

2400M-PMCL, for example, Index 0 is full black and Index

255 is full white.

LUT Value

0 to 4095

Set the LUT output value for the selected index.

* GO-2400C-PMCL only

Note

For the GO-2400C-PMCL, the same characteristic curve is configured for R, G, and B.

Содержание GO-2400C-PMCL





































































































Результаты поиска

Содержание GO-2400C-PMCL

Отзывы:

Похожие инструкции для GO-2400C-PMCL

Бренды по названию

Популярные бренды

JAI GO-2400C-PMCL, Руководство пользователя

Результаты поиска

Содержание GO-2400C-PMCL

Отзывы:

Похожие инструкции для GO-2400C-PMCL

Бренды по названию

Популярные бренды