complete
systems
for
digital
modes
E-Mail:
jäger
computing
&
services
Tel.
+49
(0)
6184
9520018
D-63517 Rodenbach Weidertsweg 8 GERMANY
http://www.jaeger-edv.de
Copyright © 2006-2016 Jäger EDV & Dienstleistungen
- 6 -
1. Esc QRES performs the command to reset the TNC2 (first perform a reset)
2. Esc I MYCALL The station call in use must be entered here.
2. Esc C AGPE01 via wide1-1, wide2-2. The TNC2 uses the terminal identification to transmit.
3. Esc M n turns off all monitor commands. Packets to control the TNC2 should
be off.
4. Esc M U turns on the non-logged packets which are needed for APRS.
5. \ # 27K switches into the KISS-mode, when successful the LEDs in the TNC2 flash 3 times.
Further TNC2-commands can be found at the following URL of DB2OS.
http://www.pocket-packet.de/thefirmware2.7_befehle.txt
During reception of an APRS-Packet (without DCD) the TNC2 is working correctly if the
yellow LED lights up. Without DCD the squelch must be closed, so that the TNC2 can send.
For each received APRS-packet an LED flashes briefly.
3. Modem – Internal Modem
Set baud rate for internal modem: For VHF 1200 baud, for short wave 300 Baud. At 300 Baud
and the mark and space frequency couples can be moved. The volume for input (audio
spectrum ) and output (microphone) is adjustable. in % “
Send Testtones”
transmits on the
internal modem
, if the hook is set. Test tones are switched on/off by pressing the enter key.
TX delay between continuous wave and data is adjustable in msec. (400)
A slot for DSP-modem (option) is available for later installation.
After each change press SAVE and then save with “save permanently” and“ restart”.
TRX1 can be operated in 2m or 70cm Band depending on the module used. The frequency is
adjustable. The baud rate can be selected with 1200 Baud or 9600 baud.
depending on the module in use.
4. Station - radio station
Enter call sign. Enter your own coordinates according to the
specification. The exact coordinates can easily be checked and taken from APRS.fi.
The QTH-locator is calculated after restart or clicking on the button.
Unproto port
is 1
Unproto address
i
s
APGE01. This address is the permanent name of the I-GATE.
Compressed beacon
checked, the coordinates will be sent in a compressed form.
Beacon comments
checked, beacon texts will be sent in the preset intervals in schedule
Time Schedules
1 - 5. Please keep the beacon texts short und use economically on
shortwave. You can reduce the texts further by inserting day and time.
The same goes for statuts texts.
Icon
Selection of the icon to be sent (soon with overlay)
Status report/beacon comments send timing
. Checked sends on short wave, delayed on KISS.
5. I-GATE - connection between the Internet and radio
Server Address
several T2 server addresses can be entered here. The address
is
listed
in
order
of
precedence. In case of server.
failure the next server is connected automatically. If the
data transit is low, use a different server. The 3 buttons below
the
server
addresses
are used to change the ranking of
the
server.
New Server
N
ew T2 server addresses can be entered here.
Validation Number
Is required to transfer data to the server. This number can be
registered
under
http://www.apritch.myby.co.uk/uiv32.htm
.
APRS server log on required
check automatically connects with the server.
Enable Auto Reconnect
check to connect again after disconnection.
The extra log on Text
changes the server behavior by Java Filter commands.
