Jade JSR Скачать руководство пользователя страница 5

 

 
P/N 2412800000 REV. C 6/2011 

 

Page 5 

toggle switch to “MANUAL”.  This will allow blower to operate and disperse excess heat rapidly 
from oven cavity (usually seconds).  When ready, place new product in oven, close door and flip 
blower switch back in the “AUTO” position. 
 
When the blower toggle switch is in the “AUTO” position, the blower will operate only with oven 
door closed.  Opening the oven door will temporarily stop blower, preventing hot air from 
blowing to operator. Closing the door will automatically set the blower to continue operation. 
 

WHEN THE OVEN IS NO LONGER IN USE, TURN OFF THERMOSTAT AND BLOWER  
SWITCH. 
 
 
 
 
 

 

SERVICE AND MAINTENANCE

 

 
Contact the factory, factory representative, or a local service company to perform maintenance 
and repairs. 
 
For daily cleaning, turn “ON” burner valves on top sections for 2 to 3 minutes and then turn 
“OFF.”  Use warm water and mild cleanser on fry top plates and open top grates.  On hot top 
plates, use a rough cloth to clean plates.  DO NOT use water to clean hot top plates. 
 

NOTE:

 

If removing hot plates for any reason, remember to replace the plate(s) with the 

underside exhaust gas opening of the plate towards the rear. All plates should fit tightly 
and flat to each other. 

 
Once a month, clean all burners with water and steel brush ensuring that all burner ports are 
free of debris.  Clean pilots in same manner.  Once cleaned and dried, re-light pilots and check 
for blockage.  As frequently as necessary, remove grease tray, empty and clean with mild 
detergent. 
 
When the appliance is supplied on casters and is connected to the supply piping by means of a 
connector for movable appliances, and removal of wall restraint becomes necessary, be sure to 
reconnect this restraint after the appliance has been turned to its originally installed position. 
 

 
SERVICE INTERVALS 

 

The need for servicing will, to a great extent, be determined by the appliance usage.  
The following chart outlines our suggestion for service intervals: 
 

DAYS PER WEEK 

SERVICE INTERVALS 

 

Normal Use 

(5 hours/day) 

Heavy Use 

(12 hours/day) 

60 Days 

30 Days 

5 to 6 

120 Days 

60 Days 

1 to 4 

180 Days 

120 Days 

CAUTION: 

Before servicing this appliance, turn OFF gas to the 

appliance and disconnect electrical supply to the appliance. 

             

 

Содержание JSR








Отзывы: