installing the panels
(where applicable)
(
3
) Fix the clips under the rim (A), by means of two self-
tapping screws to the screw anchor under the tub rim.
(
4
) Insert the corner clips on the legs in the corners of the
tub and make them slide upwards, forcing them on both sides
and arrange them inside the rim.
Then insert the stop ring in the specific groove on the leg.
(
-b
) Arrange the plastic supports (D) perpendicularly
with respect to the tub rim; then adjust in height using the
knurled ring (L).
After having reached the assembly position, lock the support
and the metallic brackets using the nut (M).
installing the side panel(s)
(where applicable)
Go to the chapter “Installing the front panel” chapter if the tub
model is not provided with side panel(s).
(
7
) Remove the protective film from the panel(s) (
detail a
).
If the tub is provided with plastic supports (D), apply the
fasteners (D2) by means of screws with washers, as shown, onto
the panel(s).
note:
Use holes “1-2” for installing the panel on the left; use holes
“3-4” for installing the panel on the right.
(
6
) Approach the side panel to the tub and press the upper
edge against the corner clips (B), inserting it between the clips
and the tub rim.
(
6
) Press the lower edge of the panel so that the fasteners
(D2) are inserted in the plastic supports (D)
(if required, adjust the
screws (V) of the supports to adjust perpendicularly of the panel)
(
detail 1
).
Proceed in the same manner to install the second side panel (if
applicable) and insert the plastic caps onto the screws (U).
installing the front panel
(
8
) Remove the protective film (
detail 1
) from the panel; in
the cases in which a seal is applied on the upper edge of the
panel, remove all traces of dirt from the panel (
detail 2
) and
apply the seal, as shown, and cut the extra part (
detail 3
).
If the tub has plastic supports, apply fasteners (D1) to the ends
of the panel by means of the screws with washers, as shown
(
detail 4
).
(
6
) Approach the front panel to the tub and press the upper
edge against the corner clips (B) and against the clips under the
rim (A), inserting it between the clips and the tub rim.
(
6
) Press the lower edge of the panel so that the fasteners
(D1) are inserted in the plastic supports (D)
(if required, adjust the
screws (V) of the supports to adjust perpendicularly of the panel)
(
detail 1
).
remove the panels
(
6
) If the panels need to be removed, e.g. for adjustment
perpendicularity, firstly remove the caps from the screw heads.
Then loosen the screws (U).
Remove the panel from the corner clips (B) and from the clips
under the rim (A), being careful not to damage the upper seal
(present on front panels).
If the tub has plastic supports (
6 detail 1
), retrieve the
fasteners from the supports and then fit them back on the panel.
general CaUtions
JACUzzI EUROPE S.p.A. will not be liable if:
the installation is performed by unqualified personnel and/or
personnel not enabled to perform the installation itself;
the rules, regulations and laws in the matter of electric systems in
buildings in force in the country where the device is installed are
disrespected;
the installation and maintenance instructions contained in this
manual are disrespected;
unsuitable and/or non-certified material is used for installation;
incorrect operations are performed which reduce the degree of
protection of jets and which modify the electrocution protection
direct or indirect contact or create isolation, current dispersion or
anomalous overheating;
changes are made to components of parts of the device with respect
to supplied conditions, which will devoid the manufacturer’s liability;
the device is repaired by unauthorised personnel or using non-
genuine spare parts made by Jacuzzi Europe S.p.A.
Jacuzzi® whirlpool products are class I, i.e. fixed appliances, and as
such are not included in the range of application of EUROPEAN
DIRECTIVE 2002/95/CE RHOS
.
If the appliance is scrapped, the component parts must be disposed
of as special waste.
Содержание Moove blower
