background image

attention new spa Owner!

Congratulations on the purchase of your new Jacuzzi® spa! The 

following is a list of automated functions performed by your spa. These 

functions are listed below in an attempt to suppress any operational 

concerns you may have during the first 24 hours of ownership! Also listed 

below are important maintenance recommendations you should observe 

on a regular basis to protect your new investment.

automated spa Operations

Your new spa is equipped with an automated “clean-up” cycle that 

clears all plumbing lines daily to promote maximum water sanitation. 

Each day at 12:00 PM (noon), each pump will activate and run for one 

minute. If either pump has just finished a 20 minute time out, it will not 

automatically activate for the clean-up cycle. Be aware, the factory 

programmed clean-up cycle cannot be canceled or altered!

maintain Healthy spa water

Always maintain your spa’s water chemistry within the following 

parameters as defined by the Association of Pool And Spa Professionals/

USA:

pH

7.4-7.6

Free chlorine

3.0-4.0 ppm

Free bromine

2.0-4.0 ppm

Total Alkalinity

100-120 ppm

Calcium Hardness

150-250 ppm

!

 TO DeCrease rIsK OF InFeCTIOn Or DIsease!

 

Always maintain 

your spa filter as outlined below to ensure healthy spa water. Refer to 

pages 67-68 (Sec. 14.0) for additional information.

required Filter maintenance

Your new spa is equipped with an advanced water filtration system that 

provides unsurpassed water quality! To ensure maximum water quality 

at all times, you should clean the skimming filter cartridge every three 

months, or as necessary. See pages 67-68 (Sec. 14.0) for detailed filter 

cartridge cleaning instructions.

required water replacement

!

 TO DeCrease rIsK OF InFeCTIOn Or DIsease!

 

You should 

replace the spa’s water every 3 months. The frequency depends on a 

number of variables including frequency of use, number of users and 

attention paid to water quality maintenance. You will know it is time for 

a change when you cannot control sudsing and/or you can no longer 

get the normal feel or sparkle to the water, even though the key water 

balance measurements are all within the proper parameters. See pages 

72-73 (Sec. 15.0) for additional information.

Содержание J - 480









































































































Отзывы: