background image

DOC NO. 81078 

Page 1 of 18 

Rev D 3/06 GM 

 

Installation Instructions 

 

Steam Shower Series 

With Fast Start Technology 

Manufacture Post 2005 

 

If you are a plumber installing this unit, please leave 

this owners manual & warranty card with the owner 

when you finish the installation. 

 

This Instruction supercedes all previous information provided by ThermaSol 

 

Thank You! 

 

CONSUMER WARNING

 

 

 

DO NOT USE THIS PRODUCT UNLESS YOU HAVE CONSULTED YOUR DOCTOR AND RECEIVED WRITTEN PERMISSION TO DO SO. 
USE OF THIS PRODUCT MAY BE HAZARDOUS TO YOUR HEALTH. 

 

 

STEAM IS HOT! DO NOT TOUCH OR GO NEAR THE STEAMHEAD FROM THE TIME THE UNIT IS  “ON”, UP TO ONE HOUR FROM THE 
TIME THE UNIT IS OFF. SEVERE BURN WILL OCCUR IF YOU COME IN CONTACT WITH THE STEAMHEAD OR STEAM EMITTING FROM 
THE STEAMHEAD. 

 

 

NEVER ATTEMPT TO FILL AROMA THERAPY RESERVOIR ON THE STEAMHEAD WHEN UNIT IS IN THE “ON” POSITION. SEVERE 
BURNS WILL OCCUR. 

 

 

DO NOT USE THERMASOL AROMA THERAPY OILS OR SKIN CARE PRODUCTS OR ANY PRODUCT IN CONJUNCTION WITH YOUR 
THERMASOL UNIT WITHOUT CONSULTING WITH YOUR ALLERGIST OR DOCTOR BEFORE USE. THESE PRODUCTS MAY BE 
HAZARDOUS TO YOUR HEALTH. 

 

 

YOUR SHOWER MAY BE A SLIP AND FALL HAZARD CHECK WITH YOUR CONTRACTOR OR FLOORING MANUFACTURER 
REGARDING THE SAFE USE OF YOUR FLOORING IN A STEAM APPLICATION. SLIPPING AND FALLING INTO THE STEAMHEAD 
ITSELF OR INTO THE STREAM OF STEAM EMITTING FROM THE STEAMHEAD WILL CAUSE SERIOUS BURNS, OR PHYSICAL INJURY. 

 

 

DO NOT USE STEAM ROOM WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS, AS THIS CAN BE HAZARDOUS TO YOUR 
HEALTH. 

 

 

IF YOU ARE FEELING UNCOMFORTABLE, DIZZY, FAINT, OR STARTING TO FALL ASLEEP IMMEDIATELY EXIT THE STEAM ROOM. 

 

 

DO NOT USE STEAM ROOM IF YOU ARE UNDER THE AGE OF 16 UNLESS SUPERVISED BY AN ADULT. 

 

Note:  Before contacting Customer Service for Technical Support, please have the model number, 
serial number and date code (located on a circle to the lower right of the serial number), include 
all numbers and letters. 

 

Headquarters & Technical Support 

2255 Union Place, Simi Valley, CA  93065 – (800) 776-0711 

Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 PST 

 

Eastern Sales Office 

26 Industrial Avenue, Fairview, NJ  07022 – (800) 631-1601 

Mon – Thur 7:00 – 5:00, Fri 8:00 – 12:00 EST 

www.thermasol.com 

Содержание SS-140



















Отзывы: