background image

J-200

•  Proper Drainage:

 

It is extremely important to have in place 

measures to sufficiently handle excessive water spillage.

 Be 

sure the flooring in which the spa rests on has adequate drainage 

and can handle the entire contents of the spa. Be sure to make 

provisions for ceilings and other structures that may be below the 

spas installation. Areas around your spa can become wet or moist so 

all flooring and subsequent furniture, walls and adjacent structures 

should be able to withstand or resist water and moisture.

•  Proper Ventilation:

 

Proper ventilation should be discussed with 

an Engineer or authority competent enough to understand the 

necessary provisions needed to vent moist or heated air and air 

associated with chemical odors outdoors.

 When the spa is in use 

considerable amounts of moisture will escape, potentially causing 

mold and mildew over time which can damage certain surfaces and/

or surroundings.

•  Sufficient Access:

 In the unlikely event that you should ever need 

to access or gain entry to any portion of the spa for servicing, it is 

highly recommended that you plan your indoor installation to provide 

full access to the entire spa.

•  Warranty:

 Damage caused by not following these guidelines or any 

improper installation not in accordance to local codes or authorities is 

not covered under the spas warranty. Please consult your local state 

or city building ordinances.

•  Do not shim the spa.

 To ensure proper support the spa must sit flat 

on the intended foundation.

11

Содержание J-200 Series

































































Отзывы: