background image

SAVE THESE INSTRUCTIONS

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal 

injury.

•  The cleaner must be installed and operated as specified.

•  This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently-

installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. 
A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its 
original integrity.

•  Clean the filter canister in the cleaner after each use.

•  Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

USE OF THE ROBOTIC CLEANER IN A VINYL LINER POOL

•  Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by objects 

coming into contact with the vinyl surface, including pool brushes, pool toys, floats, fountains, chlorine dispensers, and 
automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing the surface 
with a pool brush. Ink from the pattern can also rub off during the installation process or when it comes into contact 
with objects in the pool. We are  not responsible for, and the Limited Warranty does not cover, pattern removal, abrasion 
or markings on vinyl liners.

SECTION 2. CLEANER 

SPECIFICATIONS 

2.1  TECHNICAL SPECIFICATIONS

The general specifications for the cleaner are as 
follows:

Control box supply voltage 

1

00

-125 VAC, 60 Hz 

Supply voltage

30 V  DC

Installed load

150 W  max

The cleaner is a double-insulated product. A double-
insulated electrical appliance is one which has been 
designed in such a way that it does not require a safety 
connection to ground. The basic requirement for 
double-insulation is that no single failure can result in 
dangerous voltage becoming exposed so that it might 
cause an electric shock and that this is achieved without 
relying on an earthed (grounded) metal casing. This is 
achieved by having two (2) layers of insulating material 
surrounding live parts or by using reinforced insulation. 
Therefore, devices having double-insulated construction, 
such as this cleaner, do not utilize a grounded (three-
prong) cord/plug

5

OWNER'S MANUAL

Содержание EN27 Series

















Отзывы: