Jacobsen Super LF 1880 67955 Скачать руководство пользователя страница 40

Страница: 40 / 54

9 ADJUSTMENTS

9.12 BEDKNIFE ADJUSTMENT __________________________________________________

Read

Section 9.11

before making the adjustment.

Start adjustment at the leading end of the reel,
followed by the trailing end.

The leading end of the

reel blades is that end which passes over the
bedknife first during normal reel rotation.

Use adjusters

and

, to adjust gap. Rotate

adjusters (Clockwise) to close gap. Each click of the
adjuster moves the bedknife 0.001” (0.025 mm)
closer to the reel.

Slide a feeler gauge or shim stock 0.001” - 0.003”
(0.025 - 0.075 mm) between the reel blade and
the bedknife. Do not turn the reel.

Adjust the trailing end of the reel to the same
gap in a similar manner then recheck the
adjustment at the leading end.

When the reel is properly adjusted to the
bedknife, the reel will spin freely and you should
be able to cut a piece of newspaper, along the
full length of the reel, when the paper is held at
90° to the bedknife.

Figure 9L

9.13 CUTTING HEIGHT _________________________________________________________

Note:

Always make the reel to bedknife adjustment

before adjusting height of cut. (

Sections 9.11 and 9.12

)

Raise mowers to transport position then engage the
parking brake, stop engine, and remove key from
ignition switch.

Set desired cutting height on the gauge

(D)

Measure distance between the underside of
screw head and gauge block surface

(E)

Adjust screw

(F)

to obtain desired height then

tighten the wing nut.

Loosen the nuts

(G)

on the front roller brackets just

enough to allow the adjuster knob

(I)

to raise or lower

the front roller.

Place gauge

(D)

across bottom of front and rear

rollers near one end of roller.

Slide the head of gauge screw

(F)

over the bedknife

(H)

and adjust the knob

(I)

to close the gap between

the screw head and bedknife. Then tighten locknut

(G)

Repeat Steps 4 and 5 on opposite end. Complete
adjustment to one end before adjusting opposite end.

Tighten nuts

(G)

and recheck each end.

Figure 9M

NOTICE

Avoid excessive tightening or serious damage may
result to bedknife and reel blades. Reels must turn
freely.

Содержание Super LF 1880 67955























































Результаты поиска

Содержание Super LF 1880 67955

Отзывы:

Похожие инструкции для Super LF 1880 67955

Бренды по названию

Популярные бренды

Jacobsen Super LF 1880 67955, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Super LF 1880 67955

Отзывы:

Похожие инструкции для Super LF 1880 67955

Бренды по названию

Популярные бренды