Jacobsen Super LF 1880 67955 Скачать руководство пользователя страница 31

Страница: 31 / 54

MAINTENANCE 8

8.13 MUFFLER AND EXHAUST ___________________________________________________

To protect from carbon monoxide poisoning, inspect the
complete exhaust system regularly and always replace a
defective muffler.

If you notice a change in the color or sound of the exhaust,
stop the engine immediately. Identify the problem and have
the system repaired.

Torque all exhaust manifold hardware evenly. Tighten or
replace leaking exhaust clamps.

8.14 TIRES ___________________________________________________________________

Keep tires properly inflated to prolong tire life. Check
inflation pressure while the tires are cool. Inspect tread
wear.

Check the pressure with an accurate, low pressure
tire gauge.

Keep tires inflated to:

Front : 10-12 psi (0.69 - 0.83 BAR)

Rear: 8-10 psi (0.55 - 0.69 BAR)

8.15 WHEEL MOUNTING PROCEDURE ____________________________________________

Remove dirt, grease, and oil from stud thread. Do not
lubricate threads.

Position wheel on hub and inspect to ensure full
contact between mounting surface of wheel and hub or
brake drum.

Finger tighten all hardware, then torque hardware in
criss-cross order. Always tighten nuts in the top
(12 o’clock) position.

Check and torque daily until 85-95 ft-lbs (115-128 Nm)
torque is maintained.

8.16 ROLL OVER PROTECTIVE STRUCTURE (ROPS) ________________________________

A ROPS has been installed on this mower at the factory.
Inspect it periodically and follow operating procedures
described in the

Safety & Operation Manual

Regularly inspect the seat, seat belt, mounting
hardware, and any accessories within the ROPS.

Replace all damaged parts immediately.

Once the ROPS has been subjected to any form of
impact it should be replaced.

Check and retorque all hardware. All replacement
components used for the ROPS must be as
specified in the parts list.

WARNING

Exhaust fumes contain carbon monoxide that is toxic and
can be fatal when inhaled.

NEVER

operate an engine without proper ventilation.

CAUTION

Unless you have the proper training, tools, and
experience, DO NOT attempt to mount a tire on a rim.
Improper mounting can produce an explosion which
may result in serious injury.

WARNING

Make sure the mower is parked on a solid and level
surface. Never work on a mower that is supported only
by a jack. Always use jack stands.

If only the front or rear of the mower is raised, place
chocks in front of and behind the wheels that are not
raised.

CAUTION

Do not loosen or remove bolts. Do not weld, drill,
modify, bend, or straighten a damaged rollover
protection structure.

Содержание Super LF 1880 67955























































Результаты поиска

Содержание Super LF 1880 67955

Отзывы:

Похожие инструкции для Super LF 1880 67955

Бренды по названию

Популярные бренды

Jacobsen Super LF 1880 67955, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Super LF 1880 67955

Отзывы:

Похожие инструкции для Super LF 1880 67955

Бренды по названию

Популярные бренды