Jackson RackStar 44 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 92

background image

07610-004-33-05-E

31

The manufacturer highly recommends that any maintenance and repairs not specifically
discussed in this manual be performed only by QUALIFIED SERVICE PERSONNEL. Performing

maintenance on your dishmachine may void your warranty, lead to larger problems, or even
cause harm to the operator. So if you have a question or concern, do not hesitate to contact a

QUALIFIED SERVICE AGENCY.

By following the operating and cleaning instructions in this manual, you should get the most

efficient results from the machine. As a reminder, here are some steps to take to ensure the
machine is being used the way it was designed to work:

1. Ensure that water temperatures match those listed on the machine data plate. There can be

a variety of reasons why water temperature could be too low.

2.

Ensure all strainers are clean and in place, laying flat, before operating the machine.

When

cleaning out strainers, do NOT beat them on waste cans. Wipe out strainers with a rag and
rinse under a faucet if necessary. Use a toothpick to dislodge any stubborn debris.

3.

Ensure all wash and rinse arms are secure in the machine before operating.

4. Ensure drains are closed before operating.

5. Remove as much soil from ware by hand as possible before loading into racks.

6. Do not overfill racks.

7. Ensure glasses are placed upside-down in the rack.

8.

Ensure all chemicals being injected into machine have been verified at

the correct

concentrations.

9.

Clean the machine every 24 hours or at the end of every workday per the instructions in this

manual.

10. Follow all safety procedures, whether listed in this manual or put forth by local, state,

or national codes/regulations.

PREVENTATIVE

MAINTENANCE

i

MAINTENANCE

PREVENTATIVE MAINTENANCE

«
...
37
38
39
40
41
...
»

Содержание RackStar 44





























































































Отзывы:

Нет отзывов

Похожие инструкции для RackStar 44

Бренд: Samsung Страницы: 36

Бренд: Samsung Страницы: 36

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 180

Бренд: Samsung Страницы: 180

Бренд: Samsung Страницы: 36

Бренд: Samsung Страницы: 180

Бренд: Samsung Страницы: 72

Бренд: Fisher & Paykel Страницы: 20

Бренд: ZANKER Страницы: 68

Бренд: Arctic Страницы: 68

Бренд: ZANKER Страницы: 4

Бренд: GE Страницы: 12

Бренд: Parmco Страницы: 28

MF200D80WB Series

Бренд: Midea Страницы: 44

Бренд: Samsung Страницы: 72

Бренд: Samsung Страницы: 54

Бренд: Samsung Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды