Jackson AVENGER HT-E Скачать руководство пользователя страница 13

Страница: 13 / 61

INSTRUCTIONS

INSTALLATION

CHEMICAL FEEDER

EQUIPMENT

PRIMING CHEMICAL

FEEDER PUMPS

WARNING: Some of the

chemicals used in

dishwashing may cause

chemical burns if they

come in contact with skin.

Wear protective gear when

handling these chemicals.

If any skin comes in

contact with these

chemicals, immediately

follow the instructions

provided with the

chemicals for treatment.

TO PREPARE

CHEMICAL FEEDER

PUMPS FOR

OPERATION

WARNING!

CHLORINE-BASED SANITIZERS CAN BE DETRIMENTAL TO THIS MACHINE

IF THE CHEMICAL SOLUTION IS TOO STRONG. SEE A CHEMICAL

PROFESSIONAL TO ENSURE THE DISPENSER IS SET UP CORRECTLY.

This equipment is not recommended for use with deionized water or other aggressive fluids.

Use of deionized water or other aggressive fluids will result in corrosion and failure of

materials and components and will void the manufacturer's warranty.

The bottom of the chemical container cannot be located any higher than 8” from the

floor. If the unit is equipped with the 6” or 18” table stand, the highest position will

respectively be 14” or 26” from the floor.

The AVENGER HT-E dishmachine is supplied with detergent and rinse aid chemical

feeder pumps.

The AVENGER LT-E dishmachine is supplied with detergent, rinse aid and sanitizer

chemical feeder pumps.

Locate the open ends of the chemical tubes with the tube stiffeners and place each

one in the appropriate container.

A. Red Tubing = Detergent B. Blue Tubing = Rinse Aid

C. White Tubing = Sanitizer

Chemical feeder pumps need priming when the machine is first installed or if the

chemical lines have been removed and air is allowed to enter. CAUTION! Water

must be in the sump and wash tank prior to the dispensing of chemicals. Sanitizer in

concentration is caustic and may cause damage without dilution.

1. Verify that the proper chemical tube stiffener inlet is in the proper container.

2. Use the prime buttons located on the control panel at the bottom of the unit to

prime each pump. The buttons are clearly marked as to which chemical feeder

pump they are assigned to.

3. To prime the pumps, press the button until the chemical can be observed entering

the pump.

4. Detergent is dispensed as required during the wash cycle by the timer. The

amount of detergent may need to be increased or decreased depending upon water

quality and type of detergent.

5. Rinse additive is dispensed as required into the final rinse. The amount of rinse

additive may need to be adjusted depending upon water hardness & results.

6. Please refer to "Programming Instructions for Chemical Feeder Pumps" for

instruction on adjusting the chemical feeder pumps on the Programmable Logic

Controller (PLC).

Содержание AVENGER HT-E






























































Результаты поиска

Содержание AVENGER HT-E

Отзывы:

Похожие инструкции для AVENGER HT-E

Бренды по названию

Популярные бренды

Jackson AVENGER HT-E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AVENGER HT-E

Отзывы:

Похожие инструкции для AVENGER HT-E

Бренды по названию

Популярные бренды