background image

  

C

LEARANCES 

 

1.

 

The appliance must have a minimum 
horizontal clearance from sides and 
back of unit to adjacent vertical 
combustible construction below and 
extending above the top of the unit 36 
inches from sides and 36 inches from 
back of unit.

 

 

2.

 

Do 

not

 locate this appliance under any 

overhead unprotected combustible 
construction.

 

 

3.

 

This appliance is for 

outdoor use 

only

.  

Do not

 operate in garage, 

shed, balcony or other such enclosed 
areas.

 

 

4.

 

Do not

 restrict or obstruct the flow of 

combustible and ventilation air to the 
appliance.

 

 

5.

 

Keep the area surrounding the 
appliance free of combustible 
materials, gasoline and all flammable 
liquids and vapours.

 

 

6.

 

This appliance is not intended to be 
installed in or on recreational vehicles 
and/or boats.

 

 

LP

 

G

AS 

C

YLINDER 

P

LACEMENT 

 
Cylinders must be installed according to 
assembly instructions.  Install the gas 
cylinder into the tank hole inside of the 
Jackson Pedestal. 

 

LP GAS CYLINDER 

 

QCC-1 Quick Closing Coupling 

 
Your grill is designed to be used with an 
LP gas cylinder equipped with the new 

QCC-1 Quick Closing Coupling system.  
The QCC-1 system incorporates new 
safety features required by the Canadian 
Standards Steering Committee and the 
American National Standards Institute 
(ANSI). 
 

ƒ

 

Gas will not flow until a positive 

connection has been made. 

 

ƒ

 

A thermal element will shut off flow of 

gas between 240 degrees and 300 
degrees F.  When activated, a flow-
limiting device will limit the flow of gas 
to 10 cubic feet per hour. 

 
 
 
 
 
 
 
 
 
 

The LP Gas Cylinder is not included 
with the Gas Grill.

  Be sure to purchase 

one with the QCC valve.  This valve is 
recognized by the external threads on the 
inlet port of the valve.  QCC equipped 
cylinders are available from your gas grill 
dealer.  

Any attempt to connect the 

regulator, by use of adapters or any 
other means, to any other valve could 
result in damage or fire, and may 
negate the important safety features 
designed into the QCC-1 system.

 

 

SPECIFICATIONS 

 
1.

 

All LP gas cylinders used with this 
appliance must be constructed and 
marked with the specifications for LP 
cylinders in accordance with the 
Canadian Transport Commission (CTC) 

Содержание JG3













Отзывы: