GD-04K
- 12 -
MNY51104
Erasing tel.
numbers
authorised for
relay control
EDX, x..x, x..x
For relay
Y
enter
EDY, x..x
= tel.
number (up to 100 number can be
erased).
Example
: erase telephone number
for controlled relay X by dialling in:
EDX, 777123457
None
SMS reporting initiated by triggering of the A – D inputs
Input activation
text
ATA, xx..x
For
B
input enter
ATB
etc.,
xxx..x
=
text, up to 30 characters
To erase text:
ATA , ,
(no text = no
activation reporting)
Example:
ATC, heating on
A1,
B1,
C1,
D1
Input
deactivation
text
DTA, xx..x
For
B
input enter
DTB
etc.,
xxx..x
=
text, up to 30 characters
To erase text enter:
DTA , ,
(no text
= no deactivation reporting)
Example:
DTC, heating off
A0,
B0,
C0,
D0
Telephone
numbers for
input reports
TNA, x..x, x..x
For
B
input enter
TNB
etc.,
x..x
=
tel. number, up to 100 for each
input. All previously stored numbers
are erased. To erase all numbers
for input enter:
TNA,.,
Example:
TND, 777123456,
608123456, 775145522 sets the
GD-04K to report input D events to
2 numbers
None
Input – event
calls
DNA, n
For
B
input enter
DNB
etc.,
n
= 1
(ON), 0 (OFF). If set to ON, every
SMS report is followed by a call.
Example
:
DND, 1
Disabled
Other functions
New
programming
password
NPC, xx…x
xx…x
= new programming
password, from 2 to up to 30
characters
Example:
NPC, MARTIN27
PC
SMS to get GD-
04K status –
text change
STS, xx..x
xxx..x
= text, up to 30 characters*
Example:
STS, HOW ARE YOU
STATUS
Service
telephone
numbers
STN, x..x, x..x
xxx..x
= tel. number, Up to 2
numbers can be set, previously set
numbers are erased. Service
numbers are used to report faults:
POWER FAIL
/
POWER
RECOVERY
LINE OK
(GSM signal recovery)
Other events – see
Optional
functions
To erase the service number enter:
STN,.,
åiGQp
GD-04K -
5
- MNY51104
3. Send the SMS command:
STATUS
from your cell phone to the SIM card inserted into
the GSM communicator.
4.
The communicator answers by SMS
like this:
STATUS: A0,B0,C0,D0,X0,Y0,
GSM:80%, Vcc:12.1 V
(which means that all inputs and both relay outputs are
deactivated/switched off, the GSM signal strength is 80% and the power voltage is
12.1 V). The response speed depends on current GSM network traffic. With no
response, check if the text “STATUS” has been written correctly and sent to the correct
telephone number.
6. Settings
6.1. Local setting using PC
The most comfortable way of settings the GD-04K is by computer and
GD-Link 2.0.0
(or
higher) software which allows saving the settings for the later use. Programming SW is free
for download from
www.jablotron.com
. The software requires a Windows XP operating
system or newer.
When connected to the Internet, GD-Link checks whether a new version of the GD-Link
is available. In such case an update is offered immediately. The current FW which is part of
the GD-Link package is also downloaded and once the GD-04K is connected to the PC
automatic upgrade is offered. A FW upgrade can be performed also manually by clicking
on the option
Device / Firmware update from the file
.
Connection procedure:
Connect a PC using the supplied USB cable with the miniUSB connector (2) on the
communicator´s main board.
Start the GD-Link 2.0.0 SW or higher.
According to the settings, the required action in the initial window can be chosen or the
communicator is connected automatically.
If the setting is modified offline without connected GD-04K, then to go online press the
button “Online” on the upper toolbar when the unit is connected.
Figure 2